michael collins > 1983 Ford Bronco > open folder Clutch

After the body lift i was forced a question. What to do with the mechanical clutch system.i was goin...
Hits: 418
Size: 75.48 KB
Posted: 10/11/06
After the body lift i was forced a question. What to do with the mechanical clutch system.i was goin...		here is another angle. you can see the pivet end is junk.
Hits: 427
Size: 89.19 KB
Posted: 10/11/06
here is another angle. you can see the pivet end is junk.		The rod is almost 1/2 thick.
Hits: 392
Size: 72.91 KB
Posted: 10/11/06
The rod is almost 1/2 thick.		the leagth is 23" so i need one 3" longer to off set the body lift and i added 1/2 for the taller bo...
Hits: 420
Size: 71.54 KB
Posted: 10/11/06
the leagth is 23" so i need one 3" longer to off set the body lift and i added 1/2 for the taller bo...		The equlizer rod (Below the linkage) the rectangle hole rounds out and causes slop in the shifter an...
Hits: 543
Size: 87.42 KB
Posted: 11/3/06
The equlizer rod (Below the linkage) the rectangle hole rounds out and causes slop in the shifter an...
I looked at the sprint car circuit and got a custom made rod and heim joints.
Hits: 532
Size: 84.96 KB
Posted: 10/11/06
I looked at the sprint car circuit and got a custom made rod and heim joints.		Here is a closeup of how it was going to connect the equlizer. bar
Hits: 517
Size: 82.49 KB
Posted: 10/11/06
Here is a closeup of how it was going to connect the equlizer. bar		Here is all the rod parts and the bellcrank. i found the plastic bushings were broken and had to got...
Hits: 420
Size: 98.43 KB
Posted: 10/11/06
Here is all the rod parts and the bellcrank. i found the plastic bushings were broken and had to got...		Here is the bell crank all rebuilt and ready to go back in the truck.
Hits: 534
Size: 102.51 KB
Posted: 10/11/06
Here is the bell crank all rebuilt and ready to go back in the truck.		Here is the bell crank end of the clutch rod.
Hits: 454
Size: 92.51 KB
Posted: 10/11/06
Here is the bell crank end of the clutch rod.
Here is the rod all painted and ready to reinstall.
Hits: 576
Size: 104.57 KB
Posted: 10/11/06
Here is the rod all painted and ready to reinstall.		Here is the bell crank back in the bronco.
Hits: 613
Size: 113.46 KB
Posted: 10/11/06
Here is the bell crank back in the bronco.		Here is the connection to the throw out arm.
Hits: 458
Size: 104.33 KB
Posted: 10/11/06
Here is the connection to the throw out arm.		here is a shot of the rod going up to the equlizer bar. it is here i found another issue. the hole t...
Hits: 519
Size: 108.86 KB
Posted: 10/11/06
here is a shot of the rod going up to the equlizer bar. it is here i found another issue. the hole t...		Not the cleanest hole but it will work for now.
Hits: 443
Size: 89.98 KB
Posted: 10/11/06
Not the cleanest hole but it will work for now.
Here is the top end of the hole in the floor.
Hits: 434
Size: 93.39 KB
Posted: 10/11/06
Here is the top end of the hole in the floor.		Here is the connection to the equlizer bar. This setup works great.
Hits: 519
Size: 63.43 KB
Posted: 10/11/06
Here is the connection to the equlizer bar. This setup works great. 		   
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog