|
|
Hits: 464
Size: 87.82 KB
Posted: 10/18/06
the top looks like a great place to install the Aux guages. it is wasted space on this bronco. | 
Hits: 461
Size: 83.29 KB
Posted: 10/18/06
you can see all the unused space behind the bezel. all this is is a second harness cover. you can se... | 
Hits: 437
Size: 85.44 KB
Posted: 10/18/06
I just need to trim the blue plastic at the top. | 
Hits: 410
Size: 112.45 KB
Posted: 10/18/06
i wanted these to look factory. so i looked and fount the space on the top of the radio was wasted s... | 
Hits: 602
Size: 64.34 KB
Posted: 10/18/06
these were bought from Harbor Frieght for $6. amp/water temp/oil pressure. not too bad of a set. |
Hits: 415
Size: 61.7 KB
Posted: 10/18/06
This is the back of the Harbor Frieght guage set. simple connections and easy to follow instructions... | 
Hits: 440
Size: 102.26 KB
Posted: 10/18/06
if you knew where you were going and did not install and remove the guages a few times these are goo... | 
Hits: 393
Size: 107.24 KB
Posted: 10/18/06
This is the back side of the aftermarket guages. I got this set from Pep Boys $20. The connections a... | 
Hits: 411
Size: 87.27 KB
Posted: 10/18/06
i wanted simple and easy to make and install. this adapter mounts to the factory top speaker mounts.... | 
Hits: 470
Size: 104.93 KB
Posted: 10/18/06
I coated it with some paint and it is ready to install. |
Hits: 419
Size: 91.12 KB
Posted: 10/18/06
one last angle ---still waiting for the paint to dry.....lol | 
Hits: 443
Size: 87.79 KB
Posted: 10/18/06
the dash was beat up bad in this bronco. i added a few nuts as spacers and used the factory speaker ... | 
Hits: 401
Size: 71.94 KB
Posted: 10/18/06
here is a lower view. i trimed out the plastic (if you do this watch the main wire harness across th... | 
Hits: 496
Size: 104.86 KB
Posted: 10/18/06
this was setting up the next step. the guages are just in place not completly installed. i wanted to... | 
Hits: 464
Size: 57.89 KB
Posted: 11/3/06
Here is the stock bezel before i started. |
Hits: 462
Size: 71.08 KB
Posted: 11/3/06
Here is the stock bezel. i am not too worried about chopping it up as you can see the PO did to inst... | 
Hits: 433
Size: 78.59 KB
Posted: 11/3/06
I going to remove almost all the top box. | 
Hits: 434
Size: 64.77 KB
Posted: 10/18/06
All i had to do the the bezel was trim out the top portion. this one was damaged anyway. | 
Hits: 444
Size: 93.92 KB
Posted: 10/18/06
I had to trim the radio bezle (i going to get a new one and redo i think still not sure. this works... | 
Hits: 468
Size: 76.59 KB
Posted: 10/18/06
this is lookin up from the floor. i mad a sheet metal cover for the guages. you would normally see t... |
Hits: 442
Size: 72.57 KB
Posted: 10/18/06
Here is another view of the install | 
Hits: 493
Size: 81.77 KB
Posted: 10/18/06
this looks good and is easy to read. | 
Hits: 427
Size: 104.76 KB
Posted: 10/18/06
this is the view from the driver seat. | 
Hits: 425
Size: 75.87 KB
Posted: 10/18/06
here are the SunPros install and from the drivers seat. | 
Hits: 462
Size: 62.01 KB
Posted: 10/18/06
this is the SunPros from the pas side floor. |
Hits: 428
Size: 42.33 KB
Posted: 11/3/06
To hide or trim out the guages i took a piecs of sheet metal and bent and cut it to fit the pod. i r... | 
Hits: 448
Size: 50.53 KB
Posted: 11/3/06
Here is the trim on the guagesas seen from the back. | 
Hits: 448
Size: 57.93 KB
Posted: 11/3/06
Here is another view of the trim panel. | 
Hits: 408
Size: 92.16 KB
Posted: 10/18/06
to install the water temp probe i just removed the stock sending unit and added a couple nipples and... | 
Hits: 480
Size: 73.26 KB
Posted: 10/18/06
Here are the SunPros install and working. Volts at 14 (Thanks 3G swap) oil Pressure 27 at idle and w... |
Hits: 579
Size: 81.77 KB
Posted: 11/3/06
Here are the SunPro guages working and looking good. | | | | |
After market guages