michael collins > 1983 Ford Bronco > open folder After market guages

the top looks like a great place to install the Aux guages. it is wasted space on this bronco.
Url
Tag
Img
Thumb
you can see all the unused space behind the bezel. all this is is a second harness cover. you can se...
Url
Tag
Img
Thumb
I just need to trim the blue plastic at the top.
Url
Tag
Img
Thumb
i wanted these to look factory. so i looked and fount the space on the top of the radio was wasted s...
Url
Tag
Img
Thumb
these were bought from Harbor Frieght for $6. amp/water temp/oil pressure. not too bad of a set.
Url
Tag
Img
Thumb
This is the back of the Harbor Frieght guage set. simple connections and easy to follow instructions...
Url
Tag
Img
Thumb
if you knew where you were going and did not install and remove the guages a few times these are goo...
Url
Tag
Img
Thumb
This is the back side of the aftermarket guages. I got this set from Pep Boys $20. The connections a...
Url
Tag
Img
Thumb
i wanted simple and easy to make and install. this adapter mounts to the factory top speaker mounts....
Url
Tag
Img
Thumb
I coated it with some paint and it is ready to install.
Url
Tag
Img
Thumb
one last angle ---still waiting for the paint to dry.....lol
Url
Tag
Img
Thumb
the dash was beat up bad in this bronco. i added a few nuts as spacers and used the factory speaker ...
Url
Tag
Img
Thumb
here is a lower view. i trimed out the plastic (if you do this watch the main wire harness across th...
Url
Tag
Img
Thumb
this was setting up the next step. the guages are just in place not completly installed. i wanted to...
Url
Tag
Img
Thumb
Here is the stock bezel before i started.
Url
Tag
Img
Thumb
Here is the stock bezel. i am not too worried about chopping it up as you can see the PO did to inst...
Url
Tag
Img
Thumb
I going to remove almost all the top box.
Url
Tag
Img
Thumb
All i had to do the the bezel was trim out the top portion. this one was damaged anyway.
Url
Tag
Img
Thumb
I had to trim the radio bezle (i going to get a new one and redo i think still not sure. this works...
Url
Tag
Img
Thumb
this is lookin up from the floor. i mad a sheet metal cover for the guages. you would normally see t...
Url
Tag
Img
Thumb
Here is another view of the install
Url
Tag
Img
Thumb
this looks good and is easy to read.
Url
Tag
Img
Thumb
this is the view from the driver seat.
Url
Tag
Img
Thumb
here are the SunPros install and from the drivers seat.
Url
Tag
Img
Thumb
this is the SunPros from the pas side floor.
Url
Tag
Img
Thumb
To hide or trim out the guages i took a piecs of sheet metal and bent and cut it to fit the pod. i r...
Url
Tag
Img
Thumb
Here is the trim on the guagesas seen from the back.
Url
Tag
Img
Thumb
Here is another view of the trim panel.
Url
Tag
Img
Thumb
to install the water temp probe i just removed the stock sending unit and added a couple nipples and...
Url
Tag
Img
Thumb
Here are the SunPros install and working. Volts at 14 (Thanks 3G swap) oil Pressure 27 at idle and w...
Url
Tag
Img
Thumb
Here are the SunPro guages working and looking good.
Url
Tag
Img
Thumb
    
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog