|
|
Hits: 3529
Size: 75.22 KB
Posted: 10/31/06
I got lucky and found the last of the part number on the vaccum diagram sheet. the rest of the sheet... | 
Hits: 919
Size: 109.66 KB
Posted: 10/31/06
My charcole can mount was broken so i went to the junk yard and got a new one here it is as i brough... | 
Hits: 749
Size: 86.54 KB
Posted: 10/31/06
Here it is after some cleanup. this is the back side and you can see there is a tab at the bottom th... | 
Hits: 690
Size: 87.3 KB
Posted: 10/31/06
Here is the front side of the can. it is ready to go in. this connects to the vaper recovery line in... | 
Hits: 862
Size: 120.94 KB
Posted: 10/31/06
good think i know a person in the smog business. i failed inspection due to the oil cap being wrong.... |
Hits: 820
Size: 127.28 KB
Posted: 10/31/06
I failed for a few reasons this truck is in smog confusion centrail. it is a fed 48 truck and someon... | 
Hits: 713
Size: 106.55 KB
Posted: 10/31/06
Ok on the next trip i found the EGR valve was junk and needed to be replaced. here is the old bad va... | 
Hits: 762
Size: 116 KB
Posted: 12/28/06
another view of the EGR ready to come out | 
Hits: 656
Size: 117.17 KB
Posted: 12/28/06
here is the bad EGR almost ready to come out. | 
Hits: 685
Size: 119.97 KB
Posted: 10/31/06
Here is the new EGR installed. i had to use the correct washer in the system. different calibrations... |
Hits: 603
Size: 67.77 KB
Posted: 10/31/06
i got luckey and found a FED 48 truck in the junk yard. i was missing the WOT system and the EGR tub... | 
Hits: 630
Size: 48.99 KB
Posted: 10/31/06
Here is the Vac advance system a fast cleanup and it will be installed. | 
Hits: 652
Size: 52.98 KB
Posted: 10/31/06
This is the WOT (wide open throddle) system. I did not have this on the bronco. this was another jun... | 
Hits: 558
Size: 30.41 KB
Posted: 11/6/06
Here is the WOT mount after being cleaned up and painted. | 
Hits: 582
Size: 52.08 KB
Posted: 10/31/06
here is the EGR system loop (there is the cruse control cut out switch in the upper right but that i... |
Hits: 629
Size: 89.53 KB
Posted: 10/31/06
Ok the next failure was this temp vac tree. so i have to replace it now. | 
Hits: 551
Size: 97.8 KB
Posted: 10/31/06
Here is the new 4 port tree installed. | 
Hits: 596
Size: 106.94 KB
Posted: 10/31/06
Ok next failed reason was this is a FED 48 truck so it does not require an O2 sensor so i need to di... | 
Hits: 642
Size: 83.53 KB
Posted: 12/28/06
here is the new EGR and WOT lines installed | 
Hits: 607
Size: 112.37 KB
Posted: 11/6/06
Here is one reason it failed. the PO hollowed out the cat. |
Hits: 589
Size: 71.36 KB
Posted: 10/31/06
OK the next failure reason the cat was not working correctly. (i found out the PO beat out all the c... | 
Hits: 577
Size: 65.1 KB
Posted: 10/31/06
here is a side view of the new cat. | 
Hits: 652
Size: 69.85 KB
Posted: 11/6/06
you can see the catalyst in the cat with this pic. | 
Hits: 608
Size: 112.98 KB
Posted: 10/31/06
This is the heat stove. it is needed for the warm up in the smog system. mine was in ok shape but si... | 
Hits: 620
Size: 98.82 KB
Posted: 10/31/06
hee is a diferent view of the warm up stove. |
Hits: 630
Size: 102.17 KB
Posted: 10/31/06
Here is the warm up stove all painted and reinstalled. looks good. | 
Hits: 1166
Size: 83.73 KB
Posted: 10/31/06
I had a hard time timing this beast. there are timing markes on both sides of the motor. this is the... | 
Hits: 721
Size: 95.71 KB
Posted: 10/31/06
to make things easier to time ford ran the maroks on the driver side up the timing coveryou can see ... | 
Hits: 685
Size: 96.58 KB
Posted: 10/31/06
after yanking out my hair and my mind i did find the driver side was the side to time off of, but th... | 
Hits: 673
Size: 82.24 KB
Posted: 10/31/06
here is the hail line i used a paint pen to make it easier to see when timing the truck. |
Hits: 711
Size: 95.43 KB
Posted: 10/31/06
here was one issue i had the notch did not line up with the pass side marks. i then found these mark... | | | | |
Emissions