michael collins > 1983 Ford Bronco > open folder Motor Prep

here is the block casting number
Hits: 521
Size: 69.67 KB
Posted: 12/23/06
here is the block casting number		here is the exhaust manifold numbers
Hits: 527
Size: 70.14 KB
Posted: 12/23/06
here is the exhaust manifold numbers		Here is the oil Pan gasket.
Hits: 477
Size: 25.93 KB
Posted: 2/16/07
Here is the oil Pan gasket.		the back side of the gasket.
Hits: 498
Size: 20.52 KB
Posted: 2/16/07
the back side of the gasket. 		here is the part number OS30930 from NAPA
Hits: 644
Size: 27.91 KB
Posted: 2/16/07
here is the part number OS30930 from NAPA
here is the top front of the pan gasket.
Hits: 487
Size: 35 KB
Posted: 2/16/07
here is the top front of the pan gasket.		Here is the NAPA new oil pump part number 601-1053
Hits: 582
Size: 37.66 KB
Posted: 2/16/07
Here is the NAPA new oil pump part number 601-1053		here is the new oil pump.
Hits: 675
Size: 35.82 KB
Posted: 2/16/07
here is the new oil pump.		here is the bottom of the new pump
Hits: 557
Size: 35.12 KB
Posted: 2/16/07
here is the bottom of the new pump		here is the top of the oil pump. the drive and the oil pressure side out.
Hits: 493
Size: 28.65 KB
Posted: 2/16/07
here is the top of the oil pump. the drive and the oil pressure side out.
here is the oil pressure regulator. and the oil intake side.
Hits: 527
Size: 29.66 KB
Posted: 2/16/07
here is the oil pressure regulator. and the oil intake side.		Here are both of the gaskets for the pickup tube and the pump to block.
Hits: 503
Size: 31.18 KB
Posted: 2/16/07
Here are both of the gaskets for the pickup tube and the pump to block.		Here is the new NAPA Motor mounts. Part number 602-1287
Hits: 610
Size: 39.8 KB
Posted: 2/16/07
Here is the new NAPA Motor mounts. Part number 602-1287		The other new NAPA Motormount part number 602-1286
Hits: 649
Size: 35.67 KB
Posted: 2/16/07
The other new NAPA Motormount part number 602-1286		here is one of the mounts
Hits: 650
Size: 34.25 KB
Posted: 2/16/07
here is one of the mounts
new motor mount
Hits: 518
Size: 33.57 KB
Posted: 2/16/07
new motor mount		new motor mount
Hits: 641
Size: 36.32 KB
Posted: 2/16/07
new motor mount		here is the new mount
Hits: 522
Size: 30.83 KB
Posted: 2/16/07
here is the new mount		here is the new clutch kit part number MU1009-1A
Hits: 692
Size: 47.19 KB
Posted: 2/16/07
here is the new clutch kit part number MU1009-1A		new clutch kit top of box
Hits: 457
Size: 73.17 KB
Posted: 2/16/07
new clutch kit top of box
the documents in the box
Hits: 525
Size: 51.13 KB
Posted: 2/16/07
the documents in the box		here is inside the box
Hits: 492
Size: 63.95 KB
Posted: 2/16/07
here is inside the box		here is the new disc- all wrapped up.
Hits: 547
Size: 64.02 KB
Posted: 2/16/07
here is the new disc- all wrapped up.		here is the other side of the disc
Hits: 639
Size: 66.51 KB
Posted: 2/16/07
here is the other side of the disc		here is the pilot bushing, throw out and alignment tool
Hits: 481
Size: 30.56 KB
Posted: 2/16/07
here is the pilot bushing, throw out and alignment tool
here is the other side of the three
Hits: 630
Size: 34.59 KB
Posted: 2/16/07
here is the other side of the three		here is the working side of the pressure plate.
Hits: 467
Size: 56.57 KB
Posted: 2/16/07
here is the working side of the pressure plate.		here is the throw out side.
Hits: 626
Size: 63.11 KB
Posted: 2/16/07
here is the throw out side.		No wonder why this was leaking oil. the oil pan gasket is sticking out all over.
Hits: 628
Size: 71.64 KB
Posted: 3/1/07
No wonder why this was leaking oil. the oil pan gasket is sticking out all over.		here is the other side. it gasket is out in many places as well.
Hits: 515
Size: 61.67 KB
Posted: 3/1/07
here is the other side. it gasket is out in many places as well.
if you look under the oil filter you can see the pan gasket sticking out all over.
Hits: 576
Size: 36.94 KB
Posted: 3/1/07
if you look under the oil filter you can see the pan gasket sticking out all over.		another view of the pan gasket sticking out. I was told the newer blocks were not tapped for the man...
Hits: 703
Size: 54.06 KB
Posted: 3/1/07
another view of the pan gasket sticking out. I was told the newer blocks were not tapped for the man...		here is the stock 2G. it is a 10-2 bolt not 12-6 but the mount will do both.
Hits: 731
Size: 66.14 KB
Posted: 3/1/07
here is the stock 2G. it is a 10-2 bolt not 12-6 but the mount will do both.		here is the other side of the 2G alt.
Hits: 519
Size: 67.28 KB
Posted: 3/1/07
here is the other side of the 2G alt.		i wanted to replace the pilot bearing and rear main seal so here was the start.
Hits: 479
Size: 62.11 KB
Posted: 3/12/07
i wanted to replace the pilot bearing and rear main seal so here was the start.
i going to give this a try first but the roller bearing might be an issue. this threads into the bus...
Hits: 660
Size: 80.29 KB
Posted: 3/12/07
i going to give this a try first but the roller bearing might be an issue. this threads into the bus...		well the screw in tool failed to get a bit due to the roller bearings. so the good old stand by is a...
Hits: 503
Size: 51.44 KB
Posted: 3/12/07
well the screw in tool failed to get a bit due to the roller bearings. so the good old stand by is a...		i got it out 1/2 inch i pulled the socket out and filled more grease in the void and put the socket ...
Hits: 635
Size: 48.35 KB
Posted: 3/12/07
i got it out 1/2 inch i pulled the socket out and filled more grease in the void and put the socket ...		the next thing was the main seal. i put a screw driver on the edge of the seal and it came right out...
Hits: 610
Size: 57.45 KB
Posted: 3/12/07
the next thing was the main seal. i put a screw driver on the edge of the seal and it came right out...		the new seal went right in with out too much fuss.
Hits: 603
Size: 66.84 KB
Posted: 3/12/07
the new seal went right in with out too much fuss.
after removing a few dozen bolts the oil pan and pan rails were off. the gasket was beat bad----it w...
Hits: 607
Size: 70.06 KB
Posted: 3/12/07
after removing a few dozen bolts the oil pan and pan rails were off. the gasket was beat bad----it w...		here is the old pump. i did not see anything wrong but since i was here and it is easier to swap a f...
Hits: 461
Size: 64.59 KB
Posted: 3/12/07
here is the old pump. i did not see anything wrong but since i was here and it is easier to swap a f...		this is dark but it is the pickup tube and there is nothing in the screen and it looks good.
Hits: 466
Size: 36.59 KB
Posted: 3/12/07
this is dark but it is the pickup tube and there is nothing in the screen and it looks good.		i got the pump out with out much fuss as well. just below the motormount bolt you can see the oil pu...
Hits: 518
Size: 36.32 KB
Posted: 3/12/07
i got the pump out with out much fuss as well. just below the motormount bolt you can see the oil pu...		this is a close up of the drive it is like a long allen wrench.
Hits: 646
Size: 73.25 KB
Posted: 3/12/07
this is a close up of the drive it is like a long allen wrench.
here is the old pump out of its home. i just need to remove the pickup tube and clean it up and inst...
Hits: 623
Size: 76.63 KB
Posted: 3/12/07
here is the old pump out of its home. i just need to remove the pickup tube and clean it up and inst...		after a good cleaning and the new gasket the pickup tube gets bolted to the new pump.
Hits: 572
Size: 110.5 KB
Posted: 3/12/07
after a good cleaning and the new gasket the pickup tube gets bolted to the new pump.		here is the other side of the tube and oil pump.
Hits: 483
Size: 99.77 KB
Posted: 3/12/07
here is the other side of the tube and oil pump.		here is the pump installed with a new pump to motor gasket.
Hits: 567
Size: 56.04 KB
Posted: 3/12/07
here is the pump installed with a new pump to motor gasket.		here is the other side of the motor withthe new pump.
Hits: 488
Size: 63.88 KB
Posted: 3/12/07
here is the other side of the motor withthe new pump.
time to toss the old gasket and clean the oil pan.
Hits: 513
Size: 61.44 KB
Posted: 3/12/07
time to toss the old gasket and clean the oil pan. 		new gaskets and a goood cleanup the pan and rails are reinstalled
Hits: 616
Size: 66.62 KB
Posted: 3/12/07
new gaskets and a goood cleanup the pan and rails are reinstalled		here is the other side of the pan installed
Hits: 475
Size: 64.69 KB
Posted: 3/12/07
here is the other side of the pan installed		I cleaned the fly wheel as bast as i could. this was in good condition.
Hits: 560
Size: 63.65 KB
Posted: 4/21/07
I cleaned the fly wheel as bast as i could. this was in good condition.		i cleaned the motor plate and installed it.
Hits: 608
Size: 69.46 KB
Posted: 4/21/07
i cleaned the motor plate and installed it.
i installed the flywheel and tourqued the bolt to the book specs.
Hits: 572
Size: 60.48 KB
Posted: 4/21/07
i installed the flywheel and tourqued the bolt to the book specs.		after cleaning the threads real good in the crank and the bolts i added some red locktite.
Hits: 541
Size: 52.43 KB
Posted: 4/21/07
after cleaning the threads real good in the crank and the bolts i added some red locktite.		time to install the new pilot bushing.
Hits: 608
Size: 62.96 KB
Posted: 4/21/07
time to install the new pilot bushing.		here is the new pilot bushing installed. i used a socket and a mallet to set it in place.
Hits: 634
Size: 49.21 KB
Posted: 4/21/07
here is the new pilot bushing installed. i used a socket and a mallet to set it in place.		Finally the new 11" clutch and pressure plate was installed. now she is ready to be installed in the...
Hits: 664
Size: 74.31 KB
Posted: 4/21/07
Finally the new 11" clutch and pressure plate was installed. now she is ready to be installed in the...
here is the pass side new motor mount
Hits: 540
Size: 41.15 KB
Posted: 7/4/07
here is the pass side new motor mount		here is the new drivers side mount installed.
Hits: 517
Size: 67.21 KB
Posted: 7/4/07
here is the new drivers side mount installed.		this is now ready for the install.
Hits: 563
Size: 75.16 KB
Posted: 3/20/07
this is now ready for the install.		  
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog