michael collins > 1983 Ford Bronco > open folder Radio

Here is thecenter dash insert for the radio. this will replace the eq and tape player and the radio.
Hits: 530
Size: 65.49 KB
Posted: 2/16/07
Here is thecenter dash insert for the radio. this will replace the eq and tape player and the radio.		here is a different angle of the 2 parts.
Hits: 556
Size: 65.49 KB
Posted: 2/16/07
here is a different angle of the 2 parts.		I needed to build a mount for the sub-amp and fuse block. I got a few of these bed rails. they make ...
Hits: 635
Size: 57.6 KB
Posted: 1/10/08
I needed to build a mount for the sub-amp and fuse block. I got a few of these bed rails. they make ...		after a few measurements i cut out the front support. This will bolt to the amp, fuse panel and to t...
Hits: 675
Size: 26.42 KB
Posted: 1/10/08
after a few measurements i cut out the front support. This will bolt to the amp, fuse panel and to t...		i found this scrap from another project. this will work fine here and i laid out where things would ...
Hits: 581
Size: 35.64 KB
Posted: 1/10/08
i found this scrap from another project. this will work fine here and i laid out where things would ...
Here is the mount from the front.
Hits: 594
Size: 36.23 KB
Posted: 1/10/08
Here is the mount from the front.		This is how it will all fit. not too bad. there is enough space so the power does not bleed into the...
Hits: 540
Size: 47.77 KB
Posted: 1/10/08
This is how it will all fit. not too bad. there is enough space so the power does not bleed into the...		after cleaning the cutout up some i hit it with primer and paint. i then bolted the front bracket to...
Hits: 607
Size: 39.11 KB
Posted: 1/10/08
after cleaning the cutout up some i hit it with primer and paint. i then bolted the front bracket to...		Here it is from the front. looks good
Hits: 542
Size: 40.99 KB
Posted: 1/10/08
Here it is from the front. looks good		all the holes were pre-drilled so I installed the sub amp to the board.. I cut alittle off each scre...
Hits: 584
Size: 48.63 KB
Posted: 1/10/08
all the holes were pre-drilled so I installed the sub amp to the board.. I cut alittle off each scre...
Here is a view from the front of the amp.
Hits: 626
Size: 48.88 KB
Posted: 1/10/08
Here is a view from the front of the amp.		I now installed the fuse block. there will be one fuse per amp.
Hits: 584
Size: 54.34 KB
Posted: 1/10/08
I now installed the fuse block. there will be one fuse per amp.		Here is a view from the front. the bracket will now bolt to the front of the pass seat. where there ...
Hits: 560
Size: 50.92 KB
Posted: 1/10/08
Here is a view from the front. the bracket will now bolt to the front of the pass seat. where there ...		ok- now for the rear amp. i looked and checked almost everywhere. i was going to cut a hidden box in...
Hits: 538
Size: 62.83 KB
Posted: 1/27/08
ok- now for the rear amp. i looked and checked almost everywhere. i was going to cut a hidden box in...		there is alot of space here. i just need to move the anchor out some and do some trimming. here is t...
Hits: 518
Size: 45.46 KB
Posted: 1/27/08
there is alot of space here. i just need to move the anchor out some and do some trimming. here is t...
this bottom mount is bolted with 14mm bolts thru the floor. i removed them and put the support to si...
Hits: 534
Size: 33.14 KB
Posted: 1/27/08
this bottom mount is bolted with 14mm bolts thru the floor. i removed them and put the support to si...		i tried to set this in a few different ways and this looks best. i was going to make a mount and bol...
Hits: 514
Size: 41.89 KB
Posted: 1/27/08
i tried to set this in a few different ways and this looks best. i was going to make a mount and bol...		a dramel makes the trim a fast and painless task. i checked the gap between the inside body and the ...
Hits: 608
Size: 42.74 KB
Posted: 1/27/08
a dramel makes the trim a fast and painless task. i checked the gap between the inside body and the ...		here are the new rear top factory location speakers. i got them from a local audio place.
Hits: 570
Size: 80.66 KB
Posted: 1/27/08
here are the new rear top factory location speakers. i got them from a local audio place.		here is the front side. these will make great sounds.
Hits: 600
Size: 70.57 KB
Posted: 1/27/08
here is the front side. these will make great sounds.
i got some 14AWG monster wire. i only want to do this once. i removed the rear pillar panel and the ...
Hits: 534
Size: 71.4 KB
Posted: 1/27/08
i got some 14AWG monster wire. i only want to do this once. i removed the rear pillar panel and the ...		to allow the top more flex i removed the drivers side rear hanger support.
Hits: 510
Size: 31.58 KB
Posted: 1/27/08
to allow the top more flex i removed the drivers side rear hanger support.		one philips screw and the holder is out. i placed it aside so it can be installed later.
Hits: 544
Size: 33.24 KB
Posted: 1/27/08
one philips screw and the holder is out. i placed it aside so it can be installed later.		i ran the wires up the driverside pillar.
Hits: 505
Size: 31.74 KB
Posted: 1/27/08
i ran the wires up the driverside pillar.		here is a closer view of the install portal i used.
Hits: 548
Size: 40.46 KB
Posted: 1/27/08
here is a closer view of the install portal i used.
If you are going to do this do it right. i got a wireless solder gun and some solder and solderless ...
Hits: 510
Size: 49.88 KB
Posted: 1/27/08
If you are going to do this do it right. i got a wireless solder gun and some solder and solderless ...		i taped the speaker wires together so they look better and stay out of the way of other things.
Hits: 567
Size: 55.55 KB
Posted: 1/27/08
i taped the speaker wires together so they look better and stay out of the way of other things.		this picture is mostly for me to remember which wire went to whick post. i i was going to use color ...
Hits: 541
Size: 54.45 KB
Posted: 1/27/08
this picture is mostly for me to remember which wire went to whick post. i i was going to use color ...		i connected the wires and put the 4 sheet metal screws in the bracket and mounted the speaker.
Hits: 500
Size: 45.97 KB
Posted: 1/27/08
i connected the wires and put the 4 sheet metal screws in the bracket and mounted the speaker.		here is the pass side speaker and it installs the same way.
Hits: 510
Size: 52.33 KB
Posted: 1/27/08
here is the pass side speaker and it installs the same way.
there was not much room i might have to put a foam spacer between the magnet and roof panel. i have ...
Hits: 479
Size: 37.75 KB
Posted: 1/27/08
there was not much room i might have to put a foam spacer between the magnet and roof panel. i have ...		ok-these stock speaker grills have 2 tabs and 2 swivel mounts. you put the tabs into the head liner ...
Hits: 550
Size: 68.01 KB
Posted: 1/27/08
ok-these stock speaker grills have 2 tabs and 2 swivel mounts. you put the tabs into the head liner ...		to keep all in some sort of org. i tined the ends of the speaker wires and installed them in the amp...
Hits: 638
Size: 44.29 KB
Posted: 1/27/08
to keep all in some sort of org. i tined the ends of the speaker wires and installed them in the amp...		ok--now to the drivers side rear door speaker. these were replaced but i did not know the quality so...
Hits: 555
Size: 34.94 KB
Posted: 1/27/08
ok--now to the drivers side rear door speaker. these were replaced but i did not know the quality so...		there was enough space to run it out under the panet without cutting it. i ran it under the trim pan...
Hits: 563
Size: 43.98 KB
Posted: 1/27/08
there was enough space to run it out under the panet without cutting it. i ran it under the trim pan...
this is the door pillar between the drivers door and the rear door after removing the floor covers (...
Hits: 496
Size: 52.93 KB
Posted: 1/27/08
this is the door pillar between the drivers door and the rear door after removing the floor covers (...		here again this is more for me. letter is hot side. i solder and shrink wrapped the connections. if ...
Hits: 482
Size: 39.68 KB
Posted: 1/27/08
here again this is more for me. letter is hot side. i solder and shrink wrapped the connections. if ...		after i got the door panel off i found out why it was so loose. here is on carrot expect to replace ...
Hits: 499
Size: 54.54 KB
Posted: 1/27/08
after i got the door panel off i found out why it was so loose. here is on carrot expect to replace ...		here is the whole door panel a few of the metal support mounts were torn from the door. you can see ...
Hits: 509
Size: 52.46 KB
Posted: 1/27/08
here is the whole door panel a few of the metal support mounts were torn from the door. you can see ...		this is a closer view. you can see it was torn right off.
Hits: 511
Size: 52.19 KB
Posted: 1/27/08
this is a closer view. you can see it was torn right off.
here is the other one that was ripped off.
Hits: 516
Size: 56.95 KB
Posted: 1/27/08
here is the other one that was ripped off.		here are the brackets. i removed the old glue and door liner. reinstalling is easy line them up wher...
Hits: 507
Size: 46.13 KB
Posted: 1/27/08
here are the brackets. i removed the old glue and door liner. reinstalling is easy line them up wher...		this was also the work of the radio shop that installed the "Upgraded speakers".............one reas...
Hits: 477
Size: 49.46 KB
Posted: 1/27/08
this was also the work of the radio shop that installed the "Upgraded speakers".............one reas...		there are 8-10 1/4" hex plastic screws holding the door pocket in place. i took them out and set the...
Hits: 472
Size: 46.51 KB
Posted: 1/27/08
there are 8-10 1/4" hex plastic screws holding the door pocket in place. i took them out and set the...		here is the front side. there was a screen on the pocket but they were lost long ago.
Hits: 528
Size: 50.58 KB
Posted: 1/27/08
here is the front side. there was a screen on the pocket but they were lost long ago.
these came with the dubs, but i think a finger would find its way in too easy.
Hits: 541
Size: 50.44 KB
Posted: 1/27/08
these came with the dubs, but i think a finger would find its way in too easy. 		i got a set of round covers from the local audio store. not too bad of cost. i drilled the door pock...
Hits: 516
Size: 50.97 KB
Posted: 1/27/08
i got a set of round covers from the local audio store. not too bad of cost. i drilled the door pock...		here it is with the screen in place. looks good
Hits: 561
Size: 60.79 KB
Posted: 1/27/08
here it is with the screen in place. looks good		here are the dubs
Hits: 522
Size: 51.8 KB
Posted: 1/27/08
here are the dubs		4 screws and the dubs are in place.
Hits: 546
Size: 54.33 KB
Posted: 1/27/08
4 screws and the dubs are in place.
i found i had to trim the door panel to fit the dubs.
Hits: 502
Size: 57.22 KB
Posted: 1/27/08
i found i had to trim the door panel to fit the dubs.		all new carrots instaled and then ready to install. I found out the power motor was in the way so ...
Hits: 530
Size: 59.88 KB
Posted: 1/27/08
all new carrots instaled and then ready to install. I found out the power motor was in the way so ...		here is the drivers side completed.
Hits: 534
Size: 60.33 KB
Posted: 1/28/08
here is the drivers side completed.		Now time to do the pass side rear door. here is the door as it started. you can see it too was missi...
Hits: 574
Size: 53.71 KB
Posted: 1/28/08
Now time to do the pass side rear door. here is the door as it started. you can see it too was missi...		to remove the door panel you remove the 2 ash tray screws. one arm rest screw and pop off the window...
Hits: 511
Size: 54.05 KB
Posted: 1/28/08
to remove the door panel you remove the 2 ash tray screws. one arm rest screw and pop off the window...
here is the stripped door. this was just after the door panel was removed.
Hits: 496
Size: 59.7 KB
Posted: 1/28/08
here is the stripped door. this was just after the door panel was removed.		8 screws remove the door pocket as it was on the other door.
Hits: 485
Size: 50.91 KB
Posted: 1/28/08
8 screws remove the door pocket as it was on the other door.		again here is the old speaker. the crimp connection was not even connected. out this speaker came.
Hits: 477
Size: 45.69 KB
Posted: 1/28/08
again here is the old speaker. the crimp connection was not even connected. out this speaker came. 		here is the new cover just sitting on the door pocket.
Hits: 467
Size: 47.49 KB
Posted: 1/28/08
here is the new cover just sitting on the door pocket.		Here is the back side of the new grill. it normally screws to the speaker and sandwhiches the door.
Hits: 482
Size: 53.41 KB
Posted: 1/28/08
Here is the back side of the new grill. it normally screws to the speaker and sandwhiches the door.
to install the grill was easy center the cover the old speaker opening. Mark the 4 mounting holes.
Hits: 471
Size: 47.5 KB
Posted: 1/28/08
to install the grill was easy center the cover the old speaker opening. Mark the 4 mounting holes.		i off set the 4 speaker mount holes and the grill holes so there was no issues.
Hits: 484
Size: 48.86 KB
Posted: 1/28/08
i off set the 4 speaker mount holes and the grill holes so there was no issues.		and here is the completed grill install
Hits: 525
Size: 49.46 KB
Posted: 1/28/08
and here is the completed grill install		i then installed the new crystal audio speaker.
Hits: 542
Size: 42.94 KB
Posted: 1/28/08
i then installed the new crystal audio speaker. 		re-install the 8 door pocket screws and the panel is almost ready for install.
Hits: 461
Size: 52.5 KB
Posted: 1/28/08
re-install the 8 door pocket screws and the panel is almost ready for install.
i went to a few different places and they were out of the correct door carrots. so i got a multi pac...
Hits: 497
Size: 23.37 KB
Posted: 1/28/08
i went to a few different places and they were out of the correct door carrots. so i got a multi pac...		a cutoff wheel in the dramil and a few seconds of trimming i made the stock looking rectangle carrot...
Hits: 510
Size: 26.75 KB
Posted: 1/28/08
a cutoff wheel in the dramil and a few seconds of trimming i made the stock looking rectangle carrot...		well in came the rain so i had to return to the house so i felt this was a good time to make the few...
Hits: 516
Size: 49.41 KB
Posted: 1/28/08
well in came the rain so i had to return to the house so i felt this was a good time to make the few...		here is the power and remote power on for the frontamp.
Hits: 479
Size: 65.21 KB
Posted: 1/28/08
here is the power and remote power on for the frontamp.		here is the amp ground. i was able to make one for each amp out of this amount of wire.
Hits: 494
Size: 54.35 KB
Posted: 1/28/08
here is the amp ground. i was able to make one for each amp out of this amount of wire.
here is the sub speaker box wiring. i need the box to be able to be removed if needed so i put a set...
Hits: 499
Size: 44.16 KB
Posted: 1/28/08
here is the sub speaker box wiring. i need the box to be able to be removed if needed so i put a set...		ok-another break in the rain. now to run the door speaker wires. this is the door sill and 3 screws...
Hits: 461
Size: 52.23 KB
Posted: 1/28/08
ok-another break in the rain. now to run the door speaker wires. this is the door sill and 3 screws...		here is the new speaker wire i ran it thru the factory routing to get in the door.
Hits: 449
Size: 58.63 KB
Posted: 1/28/08
here is the new speaker wire i ran it thru the factory routing to get in the door.		again this was a good time to fix the vapor blocker. you can see i got the connectors on the wire en...
Hits: 456
Size: 62.44 KB
Posted: 1/28/08
again this was a good time to fix the vapor blocker. you can see i got the connectors on the wire en...		there is a trim panel that crosses the rear cargo area. i took the 5 screws out and pulled the cover...
Hits: 472
Size: 53.73 KB
Posted: 1/28/08
there is a trim panel that crosses the rear cargo area. i took the 5 screws out and pulled the cover...
here is the door panel reinstalled.all that is left here is the switch trim panel.
Hits: 465
Size: 60.86 KB
Posted: 1/28/08
here is the door panel reinstalled.all that is left here is the switch trim panel.		here is the switch trim panel. it is held in by 5 friction pins. i used a trim panel and worked them...
Hits: 473
Size: 57.11 KB
Posted: 1/28/08
here is the switch trim panel. it is held in by 5 friction pins. i used a trim panel and worked them...		here is the completed door.
Hits: 466
Size: 59.47 KB
Posted: 1/28/08
here is the completed door.		here is the space below the pass seat. the sub amp and power block will work great here. out of sigh...
Hits: 494
Size: 36.36 KB
Posted: 1/28/08
here is the space below the pass seat. the sub amp and power block will work great here. out of sigh...		i bolted the mount in place and this allowed the amp to float some.
Hits: 559
Size: 39.82 KB
Posted: 1/28/08
i bolted the mount in place and this allowed the amp to float some.
lots of air is avalable.
Hits: 552
Size: 45.75 KB
Posted: 1/28/08
lots of air is avalable.		i made a small slot in the carpet for the wires. this is only seen with the seat all the way forward...
Hits: 489
Size: 61.46 KB
Posted: 1/28/08
i made a small slot in the carpet for the wires. this is only seen with the seat all the way forward...		i bolted the mount to the seat. i used some lock washers to hold it tight.
Hits: 530
Size: 37.97 KB
Posted: 1/28/08
i bolted the mount to the seat. i used some lock washers to hold it tight.		here is the amp all connected and the red is the power to the other amp and remote switch wire.
Hits: 530
Size: 55.5 KB
Posted: 1/28/08
here is the amp all connected and the red is the power to the other amp and remote switch wire.		here is the stock radio and cas. deck
Hits: 512
Size: 55.93 KB
Posted: 2/4/08
here is the stock radio and cas. deck
this is the stock cass deck and eq. we had the Ipod adapter in the tape deck since the radio was not...
Hits: 481
Size: 46.15 KB
Posted: 2/4/08
this is the stock cass deck and eq. we had the Ipod adapter in the tape deck since the radio was not...		ok - to get the radio out you need to pull the dash bezel out 4 allen bolts and a few clips it comes...
Hits: 486
Size: 58.85 KB
Posted: 2/4/08
ok - to get the radio out you need to pull the dash bezel out 4 allen bolts and a few clips it comes...		after unplugging the radio from the tuner and the tape/EQ to the tuner and the amp and speaker plugs...
Hits: 459
Size: 58.81 KB
Posted: 2/4/08
after unplugging the radio from the tuner and the tape/EQ to the tuner and the amp and speaker plugs...		you are left with these holes. one above the ac/heater adjust and one in the center of the dash.
Hits: 508
Size: 48.59 KB
Posted: 2/4/08
you are left with these holes. one above the ac/heater adjust and one in the center of the dash.		here is the stock radio plug. i need the all time hot/ switched hot and the ground out of it. the re...
Hits: 491
Size: 47.47 KB
Posted: 2/4/08
here is the stock radio plug. i need the all time hot/ switched hot and the ground out of it. the re...
while swapping out the radio i say the ac/heater adjuster was broken. i just used some super glue an...
Hits: 492
Size: 41.26 KB
Posted: 2/4/08
while swapping out the radio i say the ac/heater adjuster was broken. i just used some super glue an...		i could not find a grey storage cubbie so i opted for black. it is held in place with 4 screws (same...
Hits: 485
Size: 44.13 KB
Posted: 2/4/08
i could not find a grey storage cubbie so i opted for black. it is held in place with 4 screws (same...		ok time to swap the speakers out. this dash split and broke alot under the cover. the dash had 1 cra...
Hits: 495
Size: 62.27 KB
Posted: 2/4/08
ok time to swap the speakers out. this dash split and broke alot under the cover. the dash had 1 cra...		this was the upgraded speakers the PO had installed. these sound good and will goto the motorhome.
Hits: 473
Size: 60.02 KB
Posted: 2/4/08
this was the upgraded speakers the PO had installed. these sound good and will goto the motorhome.		4 screws and the swap was done. i installed new speaker wire as well.
Hits: 498
Size: 64.79 KB
Posted: 2/4/08
4 screws and the swap was done. i installed new speaker wire as well.
For the pass side i dropped it along the stock wire harness.
Hits: 486
Size: 48.3 KB
Posted: 2/4/08
For the pass side i dropped it along the stock wire harness.		in this picture you can see i followed the stock wire loom. the dash had broken so much i had the no...
Hits: 532
Size: 52.61 KB
Posted: 2/4/08
in this picture you can see i followed the stock wire loom. the dash had broken so much i had the no...		ok- now the wires were done time to re-install the glove box and door.
Hits: 535
Size: 44.62 KB
Posted: 2/4/08
ok- now the wires were done time to re-install the glove box and door.		here is the drivers side speaker as i started.
Hits: 551
Size: 56.89 KB
Posted: 2/4/08
here is the drivers side speaker as i started.		this is the speaker the PO had installed.
Hits: 556
Size: 49.49 KB
Posted: 2/4/08
this is the speaker the PO had installed.
here is my new speaker installed.
Hits: 492
Size: 49.24 KB
Posted: 2/4/08
here is my new speaker installed.		i ran the new wires to the new radio location. here are the 2 front speakers and antenna jack
Hits: 498
Size: 51.63 KB
Posted: 2/4/08
i ran the new wires to the new radio location. here are the 2 front speakers and antenna jack		here is the radio i was going to use. it was only in our other car 6 months. the person i paid to in...
Hits: 581
Size: 48.84 KB
Posted: 2/4/08
here is the radio i was going to use. it was only in our other car 6 months. the person i paid to in...		ok time to get power to the power block under the pass seat. on the firewall on the pass side under ...
Hits: 692
Size: 57.58 KB
Posted: 2/4/08
ok time to get power to the power block under the pass seat. on the firewall on the pass side under ...		i ran the power wire down and under the ac dryer.
Hits: 620
Size: 35.42 KB
Posted: 2/4/08
i ran the power wire down and under the ac dryer.
i went behind the raditor over flow and thru the same gromet that the antenna went thru. i just trim...
Hits: 555
Size: 58.15 KB
Posted: 2/4/08
i went behind the raditor over flow and thru the same gromet that the antenna went thru. i just trim...		here is a different view showing there was no share edgings near the wire and it does pass thru the ...
Hits: 633
Size: 37.29 KB
Posted: 2/4/08
here is a different view showing there was no share edgings near the wire and it does pass thru the ...		i had to pull the sill plate of the pass side door and lift the carpet and pull the kick panel. i ra...
Hits: 665
Size: 48.53 KB
Posted: 2/4/08
i had to pull the sill plate of the pass side door and lift the carpet and pull the kick panel. i ra...		I pull it out of the carpet next to the seat. i then soldered a end and installed it into the fuse p...
Hits: 560
Size: 59.93 KB
Posted: 2/4/08
I pull it out of the carpet next to the seat. i then soldered a end and installed it into the fuse p...		ok-now complete the radio install. i connected the full hot tot he stock radio full hot. I connected...
Hits: 585
Size: 49.66 KB
Posted: 2/4/08
ok-now complete the radio install. i connected the full hot tot he stock radio full hot. I connected...
one last look at the new "Cubbie" i going to make a non-slip bottom and hold the Ipod and cell phone...
Hits: 541
Size: 46.3 KB
Posted: 2/4/08
one last look at the new "Cubbie" i going to make a non-slip bottom and hold the Ipod and cell phone...		now to complete the back amp. i needed to move the spare tire out 3" so the new amp had room to brea...
Hits: 536
Size: 42.79 KB
Posted: 2/4/08
now to complete the back amp. i needed to move the spare tire out 3" so the new amp had room to brea...		a real fast cleanup and you can see the stock floor holes. there is a nut welded to the floor under ...
Hits: 532
Size: 49.26 KB
Posted: 2/4/08
a real fast cleanup and you can see the stock floor holes. there is a nut welded to the floor under ...		you can see the tire mount in place. it is just 2-2 1/2" out more than stock.
Hits: 559
Size: 49.72 KB
Posted: 2/4/08
you can see the tire mount in place. it is just 2-2 1/2" out more than stock.		here is all the old stock radio parts. the factory amp was located under the drivers seat.
Hits: 566
Size: 69.7 KB
Posted: 2/4/08
here is all the old stock radio parts. the factory amp was located under the drivers seat.
one last view of the old stock system
Hits: 554
Size: 67.74 KB
Posted: 2/4/08
one last view of the old stock system		ok- back to the tire install. i cut a couple 2X4 blocks to space the tire out some. i had to cut 2 4...
Hits: 529
Size: 52.86 KB
Posted: 2/4/08
ok- back to the tire install. i cut a couple 2X4 blocks to space the tire out some. i had to cut 2 4...		i then installed the plastic covers. i just used 4 drywall screws. this works fine. i then cleaned t...
Hits: 572
Size: 43.3 KB
Posted: 2/4/08
i then installed the plastic covers. i just used 4 drywall screws. this works fine. i then cleaned t...		i did not have to change the hold down for the tire. i put it on as it went on before.
Hits: 634
Size: 60.81 KB
Posted: 2/4/08
i did not have to change the hold down for the tire. i put it on as it went on before.		here is the final install. there is plenty of room for the amp and spare tire. it almost looks like ...
Hits: 576
Size: 61.52 KB
Posted: 2/4/08
here is the final install. there is plenty of room for the amp and spare tire. it almost looks like ...
you can see where the old tire stops were and where they are now. the tire does not move at all and ...
Hits: 580
Size: 28.9 KB
Posted: 2/4/08
you can see where the old tire stops were and where they are now. the tire does not move at all and ...		here is looking down from the top --you can see the amp but not from the outside window.
Hits: 511
Size: 31.9 KB
Posted: 2/4/08
here is looking down from the top --you can see the amp but not from the outside window.		the tire does not rub the window eather. there is plenty of space.
Hits: 547
Size: 52.13 KB
Posted: 2/4/08
the tire does not rub the window eather. there is plenty of space.		and i put on the tire cover as it came from the factory. a fast vaccum and she looks good. this syst...
Hits: 537
Size: 54.97 KB
Posted: 2/4/08
and i put on the tire cover as it came from the factory. a fast vaccum and she looks good. this syst...		 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog