michael collins > 1983 Ford Bronco > open folder EEC Install

i been working on the EEC and wire harness placement. I going to try and be as close the the stock 1...
Hits: 449
Size: 49.3 KB
Posted: 3/9/07
i been working on the EEC and wire harness placement. I going to try and be as close the the stock 1...		another before view
Hits: 489
Size: 55.5 KB
Posted: 3/9/07
another before view		this is the space the EEC should fit in.
Hits: 474
Size: 48.58 KB
Posted: 3/9/07
this is the space the EEC should fit in.		this is where the new harness will come thru (I hope). the wire harness on the bottom was for the Hi...
Hits: 492
Size: 61.3 KB
Posted: 3/9/07
this is where the new harness will come thru (I hope). the wire harness on the bottom was for the Hi...		this is the end of the high alt harness.
Hits: 472
Size: 60.05 KB
Posted: 3/9/07
this is the end of the high alt harness.
this is the motor side of the firewall where the EEC and harness will go. you can see the high alt h...
Hits: 529
Size: 47.58 KB
Posted: 3/9/07
this is the motor side of the firewall where the EEC and harness will go. you can see the high alt h...		the 2 rusty nuts are the ebrake mount to the right of this is where the EEC will go.
Hits: 508
Size: 68.94 KB
Posted: 3/9/07
the 2 rusty nuts are the ebrake mount to the right of this is where the EEC will go.		this is the speedo cable and firewall shot
Hits: 446
Size: 53.55 KB
Posted: 3/9/07
this is the speedo cable and firewall shot		here is another view of the harness and EEC before shot.
Hits: 469
Size: 54.4 KB
Posted: 3/9/07
here is another view of the harness and EEC before shot.		here is one last look at the fire wall bafor any work was done.
Hits: 563
Size: 56.56 KB
Posted: 3/12/07
here is one last look at the fire wall bafor any work was done.
here is the inside where the computer and harness connectors will go.
Hits: 467
Size: 57.55 KB
Posted: 3/12/07
here is the inside where the computer and harness connectors will go.		here is the EEC pocket. there is a seam running at an angle in the back of the pocket but that will ...
Hits: 541
Size: 36.75 KB
Posted: 3/12/07
here is the EEC pocket. there is a seam running at an angle in the back of the pocket but that will ...		this is the EEC mount i made a template to get the correct spacing and hole size.
Hits: 550
Size: 60.32 KB
Posted: 3/12/07
this is the EEC mount i made a template to get the correct spacing and hole size.		this was one reason i changed the front cowl as it allows alot of leaves and dirt in the cowls and r...
Hits: 498
Size: 56.72 KB
Posted: 3/12/07
this was one reason i changed the front cowl as it allows alot of leaves and dirt in the cowls and r...		i vaccumed out the leaves and dirt. thius should not be an issue any more. you can see the junk.
Hits: 451
Size: 57.29 KB
Posted: 3/12/07
i vaccumed out the leaves and dirt. thius should not be an issue any more. you can see the junk.
after some measuring and carefull cutting i got the computer mount and computer installed. it looks ...
Hits: 546
Size: 60.26 KB
Posted: 3/12/07
after some measuring and carefull cutting i got the computer mount and computer installed. it looks ...		here is under the hood with the gasket in place. i covered the connection point to keep out dirt. lo...
Hits: 546
Size: 52.01 KB
Posted: 3/12/07
here is under the hood with the gasket in place. i covered the connection point to keep out dirt. lo...		   
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog