|
|
Hits: 578
Size: 61.35 KB
Posted: 6/9/07
When we got Brutis all seemed fine. a week later we smelled anti-freeze. i looked closer and found i... | 
Hits: 492
Size: 54.96 KB
Posted: 6/9/07
here is the other side of the raditor | 
Hits: 529
Size: 41.04 KB
Posted: 6/9/07
you can see some of the leak here next to the tank. | 
Hits: 469
Size: 51.96 KB
Posted: 6/9/07
there are 3 10mm screw on the top of the fan shroud. i removed them. | 
Hits: 476
Size: 42.71 KB
Posted: 6/9/07
there are 2 more screws on the side of the shroud. |
Hits: 471
Size: 44.18 KB
Posted: 6/9/07
there are 2 more on the drivers side of the shroud as well. | 
Hits: 493
Size: 43.72 KB
Posted: 6/9/07
these are the only way to get the cooler lines off without rounding the fittings. | 
Hits: 480
Size: 52.98 KB
Posted: 6/9/07
you have to use the 3/4 hose wrench to remove the oil cooler lines. you can see the leak was worse t... | 
Hits: 467
Size: 51.29 KB
Posted: 6/9/07
the trany cooler lines are 1/2 i removed them as wel. you can see it was leaking this side too. | 
Hits: 481
Size: 50.16 KB
Posted: 6/9/07
al that is left to disconnect from the raditor is the heater return line 5/8 inch hose and the over ... |
Hits: 517
Size: 50.38 KB
Posted: 6/9/07
this is the oil cooler lines. | 
Hits: 511
Size: 64.05 KB
Posted: 6/9/07
to get the bottom shroud out you need to drop the front skid plate. i used a 10mm on the cross memeb... | 
Hits: 495
Size: 53.26 KB
Posted: 6/9/07
here is the tranny cooler side a second view | 
Hits: 495
Size: 60.69 KB
Posted: 6/9/07
the raditor came right out. i cleaned the front end so there as no oil or p/s fluid and road crud. | 
Hits: 536
Size: 65.91 KB
Posted: 6/9/07
here are most of the old parts. i did not toss anything until i knew i did not need it for any parts... |
Hits: 533
Size: 94.54 KB
Posted: 6/9/07
here is the old raditor out in the yard. | 
Hits: 530
Size: 48.7 KB
Posted: 6/9/07
while i was replaceing most of the cooling system i replaced the thermastat with a 160 degree unit. | 
Hits: 493
Size: 68.65 KB
Posted: 6/9/07
to pull out the old one it taks a 9/16 wrench and out she comes. i cleaned all the parts up before r... | 
Hits: 533
Size: 40.02 KB
Posted: 6/9/07
here is the new part and the new gasket. they swapped to an o-ring so the swap was fast and painless... | 
Hits: 538
Size: 66.14 KB
Posted: 6/9/07
make sure you install the thermastat in the correct manor--the point should point to the raditor sid... |
Hits: 526
Size: 66.69 KB
Posted: 6/9/07
reinstall the stud and the bolt and then the ground wire and then the nut. the thermastat swap is co... | 
Hits: 544
Size: 50.49 KB
Posted: 6/9/07
i caled around and found that 1-800 raditors had the best price on this i told then it was for the 4... | 
Hits: 505
Size: 51.61 KB
Posted: 6/9/07
looks all pretty in the box. | 
Hits: 586
Size: 64.65 KB
Posted: 6/9/07
here is the oil cooler side of the raditor | 
Hits: 496
Size: 59.21 KB
Posted: 6/9/07
here is a closer view of the oil cooler inside. |
Hits: 583
Size: 66.89 KB
Posted: 6/9/07
here is the tranny cooler side of the raditor. | 
Hits: 534
Size: 57.51 KB
Posted: 6/9/07
here is a closer view of the trany cooler side | 
Hits: 516
Size: 34.73 KB
Posted: 6/9/07
after making sure the raditor was seated in the lower mounts i connected the tranny cooler lines. | 
Hits: 553
Size: 52.23 KB
Posted: 6/9/07
i reconnected the oil cooler lines after replacing the o-rings. i was missing one. | 
Hits: 612
Size: 57.77 KB
Posted: 6/9/07
i replaced the heater return line and the over flow line. |
Hits: 543
Size: 67.26 KB
Posted: 6/9/07
here is the lower line. i replaced it as well. | 
Hits: 532
Size: 54.03 KB
Posted: 6/9/07
this is the NAPA number 8400 for the lower. | 
Hits: 529
Size: 68.78 KB
Posted: 6/9/07
after a good cleaning the top shroud goes back into place | 
Hits: 578
Size: 53.22 KB
Posted: 6/9/07
here is the new top hose. | 
Hits: 544
Size: 64.81 KB
Posted: 6/9/07
here s the completed job. i reconnected the front axle vent clamp to the shroud and topped the anti ... |
Raditor