michael collins > 1983 Ford Bronco > open folder Roof Repair

I had a leak in the front end so i went over the whole top seal. the rear looked in need of help. Th...
Hits: 335
Size: 42.33 KB
Posted: 12/27/07
I had a leak in the front end so i went over the whole top seal. the rear looked in need of help. Th...		I did alot of checking and i found out the flat steel roof flexes the most. I found this sealer just...
Hits: 418
Size: 52.07 KB
Posted: 12/27/07
I did alot of checking and i found out the flat steel roof flexes the most. I found this sealer just...		I washed the RV (it needed it) and then scrubed the area to be sealed with the alcohol and rags till...
Hits: 392
Size: 51.79 KB
Posted: 12/27/07
I washed the RV (it needed it) and then scrubed the area to be sealed with the alcohol and rags till...		I then cut out the correct size of roof tape. this has a silver side (TOP) and a paper side (this ne...
Hits: 375
Size: 48.81 KB
Posted: 12/27/07
I then cut out the correct size of roof tape. this has a silver side (TOP) and a paper side (this ne...		I started the 1st new seal at the edge of the old seal. there was not enough on the metal to stay se...
Hits: 438
Size: 56.01 KB
Posted: 12/27/07
I started the 1st new seal at the edge of the old seal. there was not enough on the metal to stay se...
i removed a small amount of paper and used the floor roller to roll it into the metal and all the ed...
Hits: 383
Size: 51.76 KB
Posted: 12/27/07
i removed a small amount of paper and used the floor roller to roll it into the metal and all the ed...		to make sure there was a good seal i cleaned the whole area again.
Hits: 363
Size: 52.65 KB
Posted: 12/27/07
to make sure there was a good seal i cleaned the whole area again.		the next row sealed 1/2 on the 1st line of roof seal i put down and completly covered the old seal o...
Hits: 392
Size: 35.39 KB
Posted: 12/27/07
the next row sealed 1/2 on the 1st line of roof seal i put down and completly covered the old seal o...		Here is another view of the completed job.
Hits: 415
Size: 41.12 KB
Posted: 12/27/07
Here is another view of the completed job. 		I made sure all air bubbles were worked out. this side is done.
Hits: 387
Size: 45.5 KB
Posted: 12/27/07
I made sure all air bubbles were worked out. this side is done.
Here is the front as i started it there was a hole in the center of the "V" and it was leaking down ...
Hits: 408
Size: 43.85 KB
Posted: 12/27/07
Here is the front as i started it there was a hole in the center of the "V" and it was leaking down ...		I first ran a strip over the center and made sure it was rolled in real good.
Hits: 371
Size: 69.76 KB
Posted: 12/27/07
I first ran a strip over the center and made sure it was rolled in real good.		you can see i overlapped the old seal and rolled it in good and tight
Hits: 434
Size: 45.19 KB
Posted: 12/27/07
you can see i overlapped the old seal and rolled it in good and tight		here is the last view. it now has been several heavey rains and no leaks. i am so happy. job well do...
Hits: 436
Size: 40.2 KB
Posted: 12/27/07
here is the last view. it now has been several heavey rains and no leaks. i am so happy. job well do...		 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2022 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog