|
|
Hits: 382
Size: 65.71 KB
Posted: 7/10/08
I poped the cover and saw a wiring mess. i needed to charge the battery and add a new protected ligh... | 
Hits: 366
Size: 61.5 KB
Posted: 7/10/08
i start with the negitive side first. the battery connector was corroded and the wire in poor condit... | 
Hits: 384
Size: 53.25 KB
Posted: 7/10/08
I removed the negitive wire from the battery and the solinoid pack. I was surprised there was nothin... | 
Hits: 412
Size: 50.93 KB
Posted: 7/10/08
I got new marine battery connectors. these were not to bad price and allowed a fast connection. | 
Hits: 383
Size: 49.28 KB
Posted: 7/10/08
this was an off the shelf negitive cable. it was 15" it has loops on both ends. |
Hits: 379
Size: 50.91 KB
Posted: 7/10/08
I put the new battery connector in place. i used a socket and tapped it home with a hammer. | 
Hits: 420
Size: 50.34 KB
Posted: 7/10/08
I masked off the threads and sprayed the connector with battery sealer. | 
Hits: 460
Size: 58.72 KB
Posted: 7/10/08
I ran the new negitive wire the same way the old one went. this looks alot better. i had to wait 3 d... | 
Hits: 560
Size: 48.06 KB
Posted: 7/10/08
I got the new POS wires in and now time to swap. here it is as i started. | 
Hits: 400
Size: 62.38 KB
Posted: 7/10/08
The connector almost rotted off. i found a power line to the lights and a red with white stripe wire... |
Hits: 370
Size: 42.38 KB
Posted: 7/10/08
Here are the 2 new POS cables. one to the started / generator and the other to the new power take of... | 
Hits: 360
Size: 46.3 KB
Posted: 7/10/08
I cleaned the battery post and installed the new connector. i I got lucky and had some red with whit... | 
Hits: 366
Size: 55.7 KB
Posted: 7/10/08
If you look closely you can see the red heat shrink and the new wire. | 
Hits: 368
Size: 38.97 KB
Posted: 7/10/08
here is the re-routed red wire | 
Hits: 371
Size: 49.71 KB
Posted: 7/10/08
I get these power taps from chevy trucks and suburbans at the junk yard. i needed to find a spot tha... |
Hits: 415
Size: 51.99 KB
Posted: 7/10/08
I marked the spot and drilled a couple holes---making sure it was clear under the cover and do not d... | 
Hits: 381
Size: 48.73 KB
Posted: 7/10/08
I used a couple bolts and washers and lock washers to hold the tap in place. | 
Hits: 388
Size: 59.51 KB
Posted: 7/10/08
I added a loop connector to the red/white wire and added it to the power tap. | 
Hits: 361
Size: 67.11 KB
Posted: 7/10/08
Time to feed the power tap. | 
Hits: 363
Size: 58.69 KB
Posted: 7/10/08
Here is the new wire connected to power tap. this is alittle over kill but i did not want to have a ... |
Hits: 380
Size: 56.87 KB
Posted: 7/10/08
i was going to run a mini fuse at the power tap for each line. i found this cool fuse block and deci... | 
Hits: 399
Size: 61.92 KB
Posted: 7/10/08
here is the fuse holder and the main power tap. | 
Hits: 378
Size: 57.62 KB
Posted: 7/10/08
here is a close up of the fuse box it hold 4 circuits. i drilled and bolted it to the wheel well lik... | | |
Wiring Clean up