|
|
Hits: 592
Size: 75.39 KB
Posted: 11/5/07
My rig has suffered HWB (Hot Weather Bug) since I got her. My TFI-PIP assembly just doesn't like hot... | 
Hits: 506
Size: 62.35 KB
Posted: 11/5/07
| 
Hits: 499
Size: 65.28 KB
Posted: 11/5/07
All the electronic is covered by a sticky stuff, very difficult to remove. After trying to remove th... | 
Hits: 513
Size: 45.75 KB
Posted: 11/5/07
After removing the back plate, I carefully removed the electronic circuit and the sticky stuff in or... | 
Hits: 524
Size: 46.48 KB
Posted: 11/5/07
Drilled a hole for the wires |
Hits: 507
Size: 50.28 KB
Posted: 11/5/07
| 
Hits: 517
Size: 77.93 KB
Posted: 11/5/07
After soldering cables, some hot glue | 
Hits: 443
Size: 43.52 KB
Posted: 11/5/07
For the other end of the harness I wanted a real plug to fit the module. Couldn't find one so I buil... | 
Hits: 481
Size: 67.26 KB
Posted: 11/5/07
I removed the small step in the front | 
Hits: 513
Size: 81.4 KB
Posted: 11/5/07
I used braided cable for the harness and welded female spade connectors |
Hits: 501
Size: 63.44 KB
Posted: 11/5/07
After that, placed the plug and used my glue gun to bond/protect/isolate the connectors | 
Hits: 501
Size: 58.49 KB
Posted: 11/5/07
Filled all the plug wit hot glue and closed it | 
Hits: 499
Size: 45.72 KB
Posted: 11/5/07
| 
Hits: 470
Size: 79.41 KB
Posted: 11/5/07
Final fit | 
Hits: 486
Size: 80.79 KB
Posted: 11/5/07
Some non-adhesive tape and the harness was almost ready. Later I soldered ground connections. |
Hits: 529
Size: 46.65 KB
Posted: 11/5/07
I got a heat sink from a '94. After sand blasting I removed 7 fins and partially another 2 | 
Hits: 489
Size: 36.92 KB
Posted: 11/5/07
I did it that way so the fins will keep the connector in place avoiding disconnection | 
Hits: 473
Size: 71.88 KB
Posted: 11/5/07
I was going to locate the module in the driver side fender, but decided to make the harness shorter ... | 
Hits: 449
Size: 65.4 KB
Posted: 11/5/07
I have some concerns about this location because in case my A/C belt goes the module is very close, ... | 
Hits: 470
Size: 77.76 KB
Posted: 11/5/07
Heat sink in place |
Hits: 467
Size: 52.08 KB
Posted: 11/10/07
Removed the module from the distributor and connected the dummy module harness. Picture is not good ... | 
Hits: 434
Size: 83.8 KB
Posted: 11/10/07
At this point I discovered that my harness has a problem. Cables come from the dummy module connecto... | 
Hits: 577
Size: 247.21 KB
Posted: 11/10/07
| 
Hits: 462
Size: 44.01 KB
Posted: 11/10/07
Some grease in the heat sink | 
Hits: 494
Size: 46.48 KB
Posted: 11/10/07
Plug the module to the connector before placing the module in the heat sink (otherwise you will not ... |
Hits: 454
Size: 83.05 KB
Posted: 11/10/07
Connect the module (don't need to extend the cables !!!), check timing and be sure everything is in ... | | | | |
Remote TFI