|
new Edelbrock 2V "Air Gap" intake
|
|
Edelbrock F351, predates the Performer
|
|
Australian 4bbl/2V intake with choke stove provision
|
|
Aussie 302C intake, 4bbl carb with 2V ports
|
|
factory Ford 2V 351M and 2V 351C side by side
|
|
pre-production numbers ink stamped on the EGR plate
|
|
351M/400 4V, the intake that does not exist! 4300/4350 spreadbore and 2V sized ports.
|
|
factory Ford 4V for the 4300/4350 carb
|
|
iron B&A Street Boss "Clevor" intake, note rear end seal
|
|
iron B&A Track Boss "Clevor" intake, note rear end seal
|
|
holley flange 351C intake
|
|
Shelby logo'd intake was only available "over the counter"
|
|
Shelby with a 4500 dominator carb flange
|
|
D1ZX-9425-DA-CA.jpg | Hits: 961 | Size: 47.45 KB | Posted on: 1/24/10 | Link to this image
D1ZX-9425-DA and -CA
|
|
Holley Street Dominator, 2V single plane
|
|
Holley Street Dominator runners
|
|
StripDominator1.jpg | Hits: 303 | Size: 55.83 KB | Posted on: 1/19/15 | Link to this image
|
|
StripDominator2.jpg | Hits: 278 | Size: 50.76 KB | Posted on: 1/19/15 | Link to this image
|
|
StripDominator3.jpg | Hits: 285 | Size: 45.74 KB | Posted on: 1/19/15 | Link to this image
|
|
CHI 3V Clevor intakes, 4500 dominator and 4150 flanges
|
|
Ford SVO for Yates heads, requires valley cover
|
|
carb adapter plate to mount a square flange carb on a 4300 style intake
|
|
note ear to cover the EGR passage
|
|
removablearticle.jpg | Hits: 587 | Size: 53.82 KB | Posted on: 9/17/06 | Link to this image
|
|
removablearticle2.jpg | Hits: 512 | Size: 31.34 KB | Posted on: 9/17/06 | Link to this image
|
|
3X2 interchangeable top with carbs, side view
|
|
clevelandinterchangeable6v1c.jpg | Hits: 544 | Size: 58.07 KB | Posted on: 9/17/06 | Link to this image
|
|
cast iron 2V intake w/EFI installed on it
|
|
400efiadapterplate.jpg | Hits: 456 | Size: 32.02 KB | Posted on: 2/14/07 | Link to this image
adapter plate for 400 using Cleveland intake has EFI injector holes machined in
|
|
Boss 302 CrossBoss and in-line 4bbl w/ spacer plates on a 351C
|
|
four weber carbs on 4V IR manifold side view
|
|
four Weber carbs on an individual runner manifold,top view
|
|
UltraFlowCleveland.jpg | Hits: 591 | Size: 30.92 KB | Posted on: 3/13/06 | Link to this image
prototype UltraFlow multi-point fuel injection.
|
|
a different "Bud Moore" style intake
|
|
400efiadapterplate.jpg | Hits: 465 | Size: 32.02 KB | Posted on: 3/10/07 | Link to this image
|
|
'Isolated Runner' adapter for Offy Ram
not true IR but very little shared plenum
|
|
carbs mount sideways on the Offy T-ram
|
|
side/bottom view of Enderle Offy T-ram top
|
|
Offy tunnel ram top for an Enderle injector
|
|
budmooremaxiplenum.jpg | Hits: 678 | Size: 18.06 KB | Posted on: 2/8/06 | Link to this image
NASCAR Bud Moore intake
|
|
it's a folded down tunnel ram
|
|
simulated enderle injection uses a carb on a special blower top plate and the bug catcher to cover it.
|
|
Australian 2V blower manifold
|
|
tunnel ram base converted to a supercharger intake
|
|
the blow-off valve mounts under the small middle hole
|
|
Hampton 4V blower manifold
|
|
PSE adapter allows use of any Cleveland manifold on an FE engine
|