|
Hits: 2735 Size: 39.91 KB Posted: 4/25/07 Cargo Cover & Tailgate Net
1. Cargo Cover is 5 lbs 61x3x2"
2. Tailgate Net is 56"W x 13&... | Hits: 2483 Size: 104.31 KB Posted: 5/17/09 The Bronco Cargo Net (F4TZ9855066A) is a reinforced 2-layer pocket ~56x13", and is probably rar... | Hits: 909 Size: 95.89 KB Posted: 8/7/16 '94-96 Bronco Cargo Net dimensions ~56x13"
[url=http://www.supermotors.net/registry/media/7313... | Hits: 2490 Size: 27.52 KB Posted: 4/25/07 '94-96 Bronco Cargo Cover
IF THE IMAGE IS TOO SMALL, click it.
Actual dimensions: 5 lbs 61x3x2"... | Hits: 1881 Size: 74.51 KB Posted: 4/25/07 This cover was mangled & then abandoned in a junkyard for at least a year. It's severly sunburned, ... |
Hits: 1653 Size: 69.76 KB Posted: 4/25/07 The best place to start disassembly is by removing the colored end caps from the black torque plates... | Hits: 1645 Size: 73.53 KB Posted: 4/25/07 There are 4 short pins that lock into holes in the torqe plate, so it takes some effort to pop them ... | Hits: 1596 Size: 71.48 KB Posted: 4/25/07 If the slots are aligned inside, the cap slides straight off. | Hits: 1684 Size: 74.08 KB Posted: 4/25/07 Here, the slot, pins, & mating holes are visible. | Hits: 1688 Size: 63.53 KB Posted: 4/25/07 With both end caps off, the cover can be unwrapped. Align the torque plate slot with the drum slot ... |
Hits: 1546 Size: 64.81 KB Posted: 4/25/07 The plastic might be adhered to the drum, so it may be necessary to flex it to break it loose. | Hits: 1475 Size: 35.68 KB Posted: 4/25/07 The date is printed on both sides of a Tyvek tag near the R end of the cover, at the seam on the dru... | Hits: 1610 Size: 29.63 KB Posted: 4/25/07 After the cover is stripped, wash it & put in on a flat surface in the sun to relax mild wrinkles. ... | Hits: 1429 Size: 26.92 KB Posted: 4/25/07 After driving out the LEFT roll pin (use a 3/32" drift), the torque plate, bearing, spring, and... | Hits: 1419 Size: 19.94 KB Posted: 4/25/07 After MARKING the parts for proper reassembly later, pull the torque rod out of the drum & remove th... |
Hits: 1485 Size: 43.95 KB Posted: 4/25/07 The torque spring is riveted to the rod - don't remove it. The rattle-mesh slides off easily. | Hits: 1341 Size: 33.89 KB Posted: 4/25/07 The bearing pops loose from the spring, but be sure to replace it in this direction. | Hits: 1373 Size: 32.18 KB Posted: 4/25/07 There's a black plastic rattle sleeve under the spring that should be captive (NOT removable) under ... | Hits: 1352 Size: 48.3 KB Posted: 4/25/07 The large black bearings support the weight of the cover, and should slide freely inside the drum up... | Hits: 1399 Size: 34.57 KB Posted: 4/25/07 The bearings at the L end inside the drum is usually jammed onto its stops due to the spring pressur... |
Hits: 1475 Size: 36.9 KB Posted: 4/25/07 Cross-section of the drum tube. There are 6 tabs punched in to locate the white torque rod bearings... | Hits: 1457 Size: 77.62 KB Posted: 4/25/07 Remove the 2 phillips screws from below the handle. | Hits: 1454 Size: 77.33 KB Posted: 4/25/07 Remove the handle & work the draw rod to free it from the plastic so it slides. | Hits: 1507 Size: 79.5 KB Posted: 4/25/07 Slide the draw rod far enough to expose one rivet, and turn it to the flared end. Use a small file ... | Hits: 1589 Size: 86.75 KB Posted: 4/25/07 Work the catch pin out without tearing the O-rings, and slide the draw rod out of the cover. Then r... |
Hits: 1978 Size: 75.94 KB Posted: 4/25/07 Use silicone grease on the O-rings, and teflon (PTFE) grease on the bearings. | Hits: 1401 Size: 38.96 KB Posted: 4/25/07 It's possible to remove the roll pins with the end caps in place, but it's much more difficult. | Hits: 1452 Size: 86.92 KB Posted: 4/25/07 By slightly crushing the drum, rotating a few degrees, & repeating, most dents can be pushed back ou... | Hits: 1439 Size: 42.77 KB Posted: 4/25/07 This drum is severely bent in several places, as are its torque rod & draw rod. | Hits: 1398 Size: 62.44 KB Posted: 4/25/07 After some work, the drum is much better, but still not good enough to be used. The draw rod & torq... |
Hits: 1433 Size: 64.27 KB Posted: 4/25/07 The roller assembly is ready to have the colored parts added, beginning with the cover. Slide it in... | Hits: 1547 Size: 80.73 KB Posted: 4/25/07 Left end, assembled | Hits: 1561 Size: 79.27 KB Posted: 4/25/07 Middle, assembled | Hits: 1572 Size: 83.98 KB Posted: 4/25/07 Right end, assembled | Hits: 1592 Size: 63.26 KB Posted: 4/25/07 Since I don't have a truck with the right bedwalls, I can't actually test it, but it's rolled up fla... |
Hits: 1650 Size: 41.38 KB Posted: 2/4/08 SOLD Cargo Cover (repaired) from '94-96 Eddie Bauer Bronco
Actual dimensions: 5 lbs 61x3x2" | Hits: 1830 Size: 29.51 KB Posted: 2/4/08 SOLD Cargo Cover (repaired) from '94-96 Eddie Bauer Bronco
Actual dimensions: 5 lbs 61x3x2" | Hits: 1977 Size: 42.11 KB Posted: 1/8/05 The front of the bedwall panel is the same for all '92-96, but the rear of '92-93 panels doesn't hav... | Hits: 1512 Size: 51.61 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1546 Size: 30.1 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... |
Hits: 1531 Size: 54.17 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1435 Size: 40.94 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1497 Size: 52.1 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1452 Size: 52.79 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1440 Size: 54.18 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... |
Hits: 1426 Size: 47.64 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1634 Size: 45.32 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 1520 Size: 40.98 KB Posted: 11/29/04 These pics are for adding slots to a '92-93 panel not originally molded with them, as '94-96 panels ... | Hits: 990 Size: 36.92 KB Posted: 10/23/13 Factory Bronco cargo cover fully extended. Factory cargo net missing. Aftermarket cargo tray visib... | Hits: 1277 Size: 44.03 KB Posted: 10/23/13 Factory Bronco cargo cover fully extended. |
Hits: 1286 Size: 51.93 KB Posted: 10/23/13 Fully retracted. Cargo tray is aftermarket, and factory cargo net is missing. | Hits: 772 Size: 77.82 KB Posted: 7/26/14 This is the draw rod from a cargo cover that was lying in the bed of a JY Bronco under a LARGE pile ... | Hits: 670 Size: 74.11 KB Posted: 7/26/14 This is after a few minutes' work...
[url=http://www.supermotors.net/registry/media/1031134][img]ht... | Hits: 684 Size: 73 KB Posted: 7/26/14 I probably spent 20 minutes to get it to this point.
[url=http://www.supermotors.net/registry/media... | |