P7080001.JPG
492 hits | 69.74 KB | Posted: 7/10/08
1979 Warn M8274 winch

P7080002.JPG
321 hits | 64.38 KB | Posted: 7/10/08

P7080004.JPG
322 hits | 74.8 KB | Posted: 7/10/08

P7080005.JPG
285 hits | 72.26 KB | Posted: 7/10/08

P7080006.JPG
342 hits | 68.43 KB | Posted: 7/10/08
How I stored the cable.

P7080007.JPG
283 hits | 65.39 KB | Posted: 7/10/08
I used shrink tube to redo the old weather cables. I doubled the covering and they turned out very n...

P7080008.JPG
301 hits | 72.37 KB | Posted: 7/10/08

P7080009.JPG
342 hits | 79.84 KB | Posted: 7/10/08
I took the control pack apart and cleand and tested each cylinoid. Looks alot better.

P7080010.JPG
448 hits | 66.06 KB | Posted: 7/10/08

P7080011.JPG
302 hits | 47.97 KB | Posted: 7/10/08
Also cleaned the cover.

P7090001.JPG
303 hits | 49.53 KB | Posted: 7/10/08
Oringal 2.5 hp motor.

P7090002.JPG
309 hits | 70.88 KB | Posted: 7/10/08
Motor stil works and is in good shape inside. I just used some air to clean the inside.

P7090003.JPG
347 hits | 55.44 KB | Posted: 7/10/08

P7090004.JPG
336 hits | 83.17 KB | Posted: 7/10/08
pics of the tear down

P7090005.JPG
289 hits | 79.68 KB | Posted: 7/10/08
Drive end on the Drum.

P7090006.JPG
329 hits | 45.07 KB | Posted: 7/10/08
Everything is great on the inside, no signs of wear on anything.

P7090007.JPG
354 hits | 54.79 KB | Posted: 7/10/08
Top half where motor attaches.

P7090008.JPG
1117 hits | 51.6 KB | Posted: 7/10/08
Free spool clutch

P7090009.JPG
353 hits | 44.86 KB | Posted: 7/10/08
the rest of the motor, had just a touch of rust and I later used some fine sandpaper to clean it up.

P7090011.JPG
272 hits | 82.21 KB | Posted: 7/10/08
You can see here where the Drum seal had been leaking. The seal was fine but the bushing had been se...

P7090024.JPG
318 hits | 51.23 KB | Posted: 7/10/08
Its hard to see but the bushing is inside this bore on the motor side. There is also a bushing on th...

P7100001.JPG
277 hits | 64.18 KB | Posted: 7/11/08
After everything was found to be in good condition I cleaned all the parts and used a brass brush on...

P7100002.JPG
352 hits | 47.65 KB | Posted: 7/11/08

P7100005.JPG
300 hits | 54.11 KB | Posted: 7/11/08
all the parts cleaned and painted.

P7100006.JPG
306 hits | 54 KB | Posted: 7/11/08

P7100007.JPG
329 hits | 55.64 KB | Posted: 7/11/08

P7100023.JPG
320 hits | 67.5 KB | Posted: 7/11/08

P7100020.JPG
531 hits | 56.01 KB | Posted: 7/11/08
Still have to put the motor housing on but first I add oil. It calls for 6oz of non-det 30 weight. B...

P7100025.JPG
370 hits | 56.44 KB | Posted: 7/11/08
had to show off this long alen wrench.

P7100026.JPG
298 hits | 51.03 KB | Posted: 7/11/08
looking better

P7100027.JPG
351 hits | 56.22 KB | Posted: 7/11/08

P7110030.JPG
346 hits | 61.52 KB | Posted: 7/11/08

P7110031.JPG
302 hits | 60.93 KB | Posted: 7/11/08

P7110033.JPG
310 hits | 52.95 KB | Posted: 7/11/08
in this pic you can see the bolt I welded to the motor case for a good ground.

P7110038.JPG
369 hits | 41.28 KB | Posted: 7/11/08
just trying to get a good pic of how nice this turned out.

P7110039.JPG
323 hits | 59.11 KB | Posted: 7/11/08

P7110040.JPG
322 hits | 61.03 KB | Posted: 7/11/08
all done, I will install the cable after it is mounted to the Bronco.