york mount 5.JPG 479 hits | 44.07 KB | Posted: 3/29/07 power steering clearance. this section of the bracket is gunna get reworked probably when i do my signaw swap. i'm not gunna use that bolt hole probably. (Posted in: OBA)
MM12000.JPG 564 hits | 65.64 KB | Posted: 10/26/06 that's the mnster Mile Marker SE12000C. it's about 92 lbs with the solenoid, cable, wiring, fairlead, and hook. (Posted in: winch)
154-5426_IMG.JPG 511 hits | 52.14 KB | Posted: 10/26/06 the start of the mounting plans. i kinda copied shadow fox's writeup. (Posted in: winch)
winch mock-up 1.JPG 538 hits | 68.02 KB | Posted: 10/26/06 mocking it up. it does fit. but i had to relocate the solenoid box. (Posted in: winch)
winch mock-up side.JPG 501 hits | 49.25 KB | Posted: 10/26/06 side view. i think i'm gunna either move those hooks or get some shackle mounts. (Posted in: winch)
154-5425_IMG.JPG 485 hits | 33.87 KB | Posted: 10/26/06 clearance behind the winch. that tranny hard line kept me from using the C channel. and the winch it's self is too big to fit in the smaller C channel that fits in front of that line (Posted in: winch)
pass side 1.JPG 507 hits | 54.56 KB | Posted: 1/14/07 the rust on the passengerside (Posted in: rear fender stuff)
inner fender.JPG 477 hits | 66.37 KB | Posted: 1/14/07 rust on top side of drivers side inner fender. i will be cutting all of this piece out (Posted in: rear fender stuff)
fender trim idea 1.JPG 463 hits | 59.87 KB | Posted: 1/14/07 this is the plan for the new wheel opening (Posted in: rear fender stuff)
fender trim idea 33.JPG 502 hits | 66.43 KB | Posted: 1/14/07 with a 33 (Posted in: rear fender stuff)
155-5512_IMG.JPG 445 hits | 33.57 KB | Posted: 1/14/07 drivers side rear corner damage from tire loss on freeway. (Posted in: rear fender stuff)
{}jan 07.JPG 552 hits | 79.93 KB | Posted: 1/27/07 finished product. this is the side with no damage. i will be extending the wheel base a bit when i put the one ton axles in. (Posted in: rear fender stuff)
cab corner removed.JPG 508 hits | 48.1 KB | Posted: 1/27/07 there is the undamaged corner that was cut out. (Posted in: rear fender stuff)
155-5535_IMG.JPG 460 hits | 69.07 KB | Posted: 1/27/07 i didn't remove any metal from the front of the opening. i might have to later but for now it's staying there. (Posted in: rear fender stuff)
rock slider mounts.JPG 640 hits | 57.11 KB | Posted: 1/27/07 1.5x3 inch rectangle tubing. .25 inch wall. all tig welded. (Posted in: rock sliders)
rock slider step.JPG 623 hits | 56.6 KB | Posted: 1/27/07 1.25 inch OD DOM .125 wall. having access to a good notcher and bender made this part a lot easier. (Posted in: rock sliders)
{}jan 07.JPG 627 hits | 79.93 KB | Posted: 1/27/07 i had to leave a cut out in the slider for the exhaust. when the exhaust gets torn off i've got some extra rectangle tubing to fill in the space. (Posted in: rock sliders)
