Img_0334.jpg 1896 hits | 80.8 KB | Posted: 3/8/04 AC compresser is gonna sit on top until I get a AC/PS bracket...to make a long story short I didnt have a Sag bracket and wanted one to use my sag pump. (Posted in: 460 project)
DCP_0549.jpg 1898 hits | 79.06 KB | Posted: 6/28/04 Morning after the Friday All-Nighter First Trail Run up lower section of Ravens Roost. About 3 miles in 6 hours. The Rock Sliders are Worth Every Second of Fab Time. Put Them to Use About Half Dozen Times. (6/26/2004) (Posted in: Bronco Fest NW 2004)
DSC01428.JPG 1903 hits | 99.12 KB | Posted: 3/13/05 My puppy Bremen on her first wheelin' trip (Posted in: English Mountain, TN)
CENTURION (R) FRONT.JPG 1903 hits | 62.56 KB | Posted: 7/6/03 (R) FRONT - 460HP HOOD SCOOP - NOTICE THE CHROME GOODIES ON THE FRONT - HEY - IS THAT A DAMN BOAT CLEAT? (Posted in: 1986 CENTURION)
DCP_0840.jpg 1905 hits | 52.21 KB | Posted: 8/7/05 Rock Slider Rear Quarters
(8/6/2005) (Posted in: Rock Slider Rear Quarters)
tailgate_powerwindow_schematic.jpg 1909 hits | 48.78 KB | Posted: 6/29/03 Wiring schematic for window, aplies to 1980 - 1986 Broncos. Ford changed the look and moved the dash switch but it works the same way. (Posted in: Tailgate)
fuelfilter2.jpg 1913 hits | 51.47 KB | Posted: 6/29/03 Overview of the entire system (Posted in: Fuel System)
DSC00018.jpg 1914 hits | 25.61 KB | Posted: 6/29/03 You can buy this top of the line fiberglass tailgate from Autofab in CA. Sit down, its $750! (Posted in: Tailgate)
DCP_0895.jpg 1934 hits | 40.44 KB | Posted: 4/30/06 Bottom Mounting Brackets
The bottom mounting brackets carry the weight and sit on the tray under the radiator. There are 4 (3 visible in picture) C shape brackets made of 1/16 x 3/4 aluminum flat stock.
Did not use any of the manufactures supplied... (Posted in: Electric Cooling Fan)
DCP_0597.jpg 1936 hits | 54.81 KB | Posted: 7/21/04 Profile of 'L' Bracket, Receiver, and Mounting to Sway Bar Bracket
'L' Bracket is 3" x 3/8" and mounts to bottom of sway bar bracket and to the back of the bumper bracket.
The receiver/winch plate is 8" x 4" x 1/2" angle and mounts to bottom ... (Posted in: Front Receiver)
DCP_0898.jpg 1936 hits | 57.6 KB | Posted: 4/30/06 Top Mounting Brackets
The top mounting brackets hold the shroud against the radiator core but do not carry any weight and are made of 1/16 x 3/4 aluminum flat stock.
Did not use any of the manufactures supplied mounting bracketry.
(4/29/2006)
(Posted in: Electric Cooling Fan)
newrims2.jpg 1938 hits | 22.5 KB | Posted: 7/28/03 Another view....seems so "short" now looking back to pre lift pictures (Posted in: Rims)
Ford 10.25 (Axle Code 35):
RABS Sensor
Park Brake Cables
4" Blocks (factory) with Integrated Bump Stops Arms
Driveshaft
Misellaneous Parts:
Steering Gear Box
Pitman Arm
Steering Shaft
Washer Fluid Rese... (Posted in: Pot of Gold)
012-Jims-Back.JPG 1939 hits | 107.58 KB | Posted: 12/15/03 Jim returns to find his truck has 4" of new snow (white mud) (Posted in: Mt.Hood Xmas Tree 2003-12-13)
controlarm07.JPG 1939 hits | 47.36 KB | Posted: 6/30/03 shot of the other side (Posted in: Extended radius arms)
DCP_0904.jpg 1940 hits | 52.69 KB | Posted: 4/30/06 Variable Speed Controller
The variable speed controller is mounted on the fan shroud.
Wiring is zip tied to the shroud to keep them away from the fan blades.
The VSC also has overrides for Off, and High. However the A/C compressor negative sign... (Posted in: Electric Cooling Fan)
 FRONT.JPG)
.jpg)
