SideView.jpg
639 hits | 69.06 KB | Posted: 3/8/06
Side shot of the voltage regulator
(Posted in: Voltage Regulator Swap)

ScrewRemoved.jpg
682 hits | 79.45 KB | Posted: 3/8/06
When the screws are removed the voltage regulator will be pushed up by the brushes.
(Posted in: Voltage Regulator Swap)

ScrewRemovedSide.jpg
683 hits | 60.07 KB | Posted: 3/8/06
Another shot with the screws removed. The regulator simply lifts out.
(Posted in: Voltage Regulator Swap)

VoltReg3.pg.jpg
654 hits | 52.36 KB | Posted: 3/8/06
Voltage regulator. (The 2 screws in the picture hold the brush assembly to the regulator. T20 Torx bit)
(Posted in: Voltage Regulator Swap)

VoltReg1.jpg
661 hits | 46.47 KB | Posted: 3/8/06
Side view....showing brush assembly
(Posted in: Voltage Regulator Swap)

Brushes.jpg
671 hits | 65.01 KB | Posted: 3/8/06
This is the brush assembly bolted in place on the back of the voltage regulator
(Posted in: Voltage Regulator Swap)

BrushesRemoved.jpg
657 hits | 54.12 KB | Posted: 3/8/06
When you remove the 2 screws....the brush assembly simply comes off of the regulator
(Posted in: Voltage Regulator Swap)

BrushesRemovedTop.jpg
681 hits | 45.93 KB | Posted: 3/8/06
Another shot of the brushes removed
(Posted in: Voltage Regulator Swap)

BrushesScrewsLoose.jpg
706 hits | 65.5 KB | Posted: 3/8/06
Brush assembly screws loosened
(Posted in: Voltage Regulator Swap)

BrushRetainer.jpg
667 hits | 55.8 KB | Posted: 3/8/06
When you go to reinstall the regulator the brushes have to be held back into the housing. Use a paper clip to hold them in place.
(Posted in: Voltage Regulator Swap)

Brushes1.jpg
646 hits | 54.66 KB | Posted: 3/8/06
With the retaining screws tight, press the brushes into the housing.
(Posted in: Voltage Regulator Swap)

BrushesLocked.jpg
654 hits | 60.38 KB | Posted: 3/8/06
Here you can see that the brushes are held in place with the paper clip
(Posted in: Voltage Regulator Swap)

BrushesLocked1.jpg
740 hits | 58.68 KB | Posted: 3/8/06
Another view of the brushes held in place
(Posted in: Voltage Regulator Swap)

InstallingReg.jpg
669 hits | 76.66 KB | Posted: 3/8/06
To install, simply lay the regulator into place.
(Posted in: Voltage Regulator Swap)

InstallingReg1.jpg
607 hits | 82.94 KB | Posted: 3/8/06
Ready to bolt in
(Posted in: Voltage Regulator Swap)

InstallingReg2.jpg
650 hits | 77.12 KB | Posted: 3/8/06
Tighten the mounting bolts
(Posted in: Voltage Regulator Swap)

RemovingLock.jpg
648 hits | 64.24 KB | Posted: 3/8/06
When the regulator is in place and screws tightened, pull the paper clip out.
(Posted in: Voltage Regulator Swap)

RemovingLock1.jpg
671 hits | 66.17 KB | Posted: 3/8/06
You will hear the brushes pop out of the housing.....and your done!
(Posted in: Voltage Regulator Swap)

P1000054.jpg
648 hits | 121.62 KB | Posted: 7/31/06
Can you believe it was left in a parking lot?
(Posted in: 1992 Mustang LX)

P1000056.jpg
673 hits | 111.13 KB | Posted: 7/31/06
Someone started body work. Plenty of work still too do
(Posted in: 1992 Mustang LX)

P1000058.jpg
658 hits | 102.82 KB | Posted: 7/31/06
A little weathered.
(Posted in: 1992 Mustang LX)

P1000060.jpg
709 hits | 91.61 KB | Posted: 7/31/06
Needs a good cleaning, but not bad for an abandoned car
(Posted in: 1992 Mustang LX)

P1000071.jpg
676 hits | 101.04 KB | Posted: 7/31/06
Bone stock 5.0. Completely un-molested....even the air silencer is in the fender!
(Posted in: 1992 Mustang LX)

avatar3.jpg
681 hits | 10.37 KB | Posted: 8/9/06
(Posted in: 2001 Grand Marquis)

Left5.jpg
2117 hits | 37.09 KB | Posted: 6/30/03
(Posted in: Exterior)

8x6.jpg
1347 hits | 32.17 KB | Posted: 6/30/03
(Posted in: Exterior)

8x6-2.JPG
1230 hits | 31.81 KB | Posted: 6/30/03
(Posted in: Exterior)

LeftAngle7tn.JPG
1272 hits | 31.81 KB | Posted: 6/30/03
(Posted in: Exterior)

8-02-03-2.gif
1164 hits | 67.67 KB | Posted: 8/3/03
8-02-2003
(Posted in: Exterior)

PICT0019.jpg
1163 hits | 62.1 KB | Posted: 7/26/04
6-26-2004
(Posted in: Exterior)

PICT0129.jpg
1212 hits | 59.86 KB | Posted: 11/17/04
9-2004
(Posted in: Exterior)

PICT0113.jpg
1475 hits | 37.26 KB | Posted: 11/17/04
(Posted in: Exterior)

HP Design EVO 19 Inch Wheels.jpg
3362 hits | 53.65 KB | Posted: 4/12/05
4-10-2005
(Posted in: Exterior)

PICT0002.jpg
1353 hits | 44.56 KB | Posted: 4/12/05
19x9.5 Wheels with 285/35/19 Tires
(Posted in: Exterior)

Signature.JPG
1204 hits | 18.34 KB | Posted: 4/12/05
(Posted in: Exterior)

4-13-05.jpg
1271 hits | 49.5 KB | Posted: 4/14/05
4-13-05
(Posted in: Exterior)

Front.jpg
1178 hits | 65.69 KB | Posted: 4/14/05
(Posted in: Exterior)

Rear.jpg
1182 hits | 69.44 KB | Posted: 4/14/05
(Posted in: Exterior)

GRM.JPG
1336 hits | 90.6 KB | Posted: 1/1/06
Grassroots Motorsports Magazine
Internet.Hot.Rod.Of.The.Month feature
(Posted in: Exterior)

Vortex Cherrybomb Mufflers.wmv
1246 hits | 1.95 MB | Posted: 4/9/06
Vortex Cherrybomb mufflers with Magnaflow high flow cats on an X-piped 2 1/4" exhaust.
(Posted in: Exterior)

PICT17348.jpg
1326 hits | 67.01 KB | Posted: 5/8/07
05-07-07
(Posted in: Exterior)

Avatar11.JPG
1099 hits | 35.6 KB | Posted: 6/4/07
(Posted in: Exterior)

PICT0069.jpg
1659 hits | 33.92 KB | Posted: 6/30/03
So far untouched.
(Posted in: Engine Compartment)

KN-3.jpg
1366 hits | 50.81 KB | Posted: 6/30/03
K&N Filter Added.
(Posted in: Engine Compartment)

Brakes_and_Front_Rotor.JPG
831 hits | 42.36 KB | Posted: 6/30/03
Power Slot Front Rotor and Hawk Brake Pads
(Posted in: Powerslot Rotors)