IMG_20160326_191354738.jpg
165 hits | 24.86 KB | Posted: 8/10/16
(Posted in: 1965 galxie LTD)

IMG_20160326_191532867.jpg
176 hits | 35.11 KB | Posted: 8/10/16
(Posted in: 1965 galxie LTD)

IMG_20160326_191542718.jpg
177 hits | 35.46 KB | Posted: 8/10/16
(Posted in: 1965 galxie LTD)

2222.JPG
160 hits | 70.65 KB | Posted: 5/20/16
Rotten floor pan. Need to fix this.
(Posted in: Floor pans and carpet)

3333.JPG
151 hits | 46.32 KB | Posted: 5/20/16
Bad on on side, new on the other. Just cut out of 20-gauge sheet.
(Posted in: Floor pans and carpet)

6666.JPG
144 hits | 44.73 KB | Posted: 5/20/16
New and old. Takes a lot of trimming to get a good butt weld.
(Posted in: Floor pans and carpet)

IMG_2875.JPG
167 hits | 73.81 KB | Posted: 5/20/16
Console mock up with lid and drawer.
(Posted in: Center console )

IMG_2885 (Edited).JPG
163 hits | 59.46 KB | Posted: 5/20/16
Trim ring and gauges set in place.
(Posted in: Center console )

IMG_2901.JPG
165 hits | 51.86 KB | Posted: 5/20/16
Drawer and lid installed all open.
(Posted in: Center console )

IMG_2902.JPG
138 hits | 50.2 KB | Posted: 5/20/16
Drawer and lid installed all closed.
(Posted in: Center console )

IMG_2881 (Edited).JPG
111 hits | 45.38 KB | Posted: 5/20/16
Driver's side bungs welded.
(Posted in: Megasquirt fuel injection)

IMG_2882 (Edited).JPG
130 hits | 50.87 KB | Posted: 5/20/16
Passenger side bungs welded.
(Posted in: Megasquirt fuel injection)

IMG_2883 (Edited).JPG
119 hits | 62.38 KB | Posted: 5/20/16
Fuel rail mockup.
(Posted in: Megasquirt fuel injection)

IMG_2884 (Edited).JPG
107 hits | 58.42 KB | Posted: 5/20/16
Bungs ground flush inside intake runners.
(Posted in: Megasquirt fuel injection)

IMG_2895.JPG
108 hits | 75.19 KB | Posted: 5/20/16
Intake bolted down and rails on checking for clearance.
(Posted in: Megasquirt fuel injection)

IMG_2896.JPG
135 hits | 61.26 KB | Posted: 5/20/16
Another shot of the intake and rails. Turns out the rails clear but not the fittings. Had to melt a little of the wiper box away but nothing too bad.
(Posted in: Megasquirt fuel injection)

IMG_2897.JPG
129 hits | 59.22 KB | Posted: 5/20/16
Custom chisel I made to fix the slight bulge the welder left in on bung.
(Posted in: Megasquirt fuel injection)

IMG_2967.JPG
101 hits | 49.32 KB | Posted: 5/20/16
Megasquirt bolted up behind the glove box.
(Posted in: Megasquirt fuel injection)

IMG_2968.JPG
105 hits | 51.15 KB | Posted: 5/20/16
View of the ECM from the passenger foot well.
(Posted in: Megasquirt fuel injection)

IMG_2969.JPG
129 hits | 68.05 KB | Posted: 5/20/16
Aluminum panel for fuse and relay blocks.
(Posted in: Megasquirt fuel injection)

IMG_2970.JPG
119 hits | 71.67 KB | Posted: 5/20/16
Electrical distribution center.
(Posted in: Megasquirt fuel injection)

bt1.JPG
93 hits | 78.94 KB | Posted: 5/20/16
Pile of parts ready to install.
(Posted in: Trunk mounted battery)

bt4.JPG
94 hits | 75.45 KB | Posted: 5/20/16
Flexible conduit running down channel by doors. Well protected.
(Posted in: Trunk mounted battery)

bt5.JPG
89 hits | 74.43 KB | Posted: 5/20/16
Conduit coming out in engine compartment. Came up through a factory hole.
(Posted in: Trunk mounted battery)

IMG_2549.JPG
95 hits | 37 KB | Posted: 5/20/16
Vent tube. Epoxied into the fitting and to the floor. No movement, no leaks.
(Posted in: Trunk mounted battery)

IMG_2559.JPG
154 hits | 74.95 KB | Posted: 5/20/16
Crimp fitting, solder to cover the open end, marine heat shrink to seal and act as strain relief. That's how I do it at least.
(Posted in: Trunk mounted battery)

IMG_2906.JPG
88 hits | 49.97 KB | Posted: 5/20/16
Pump and pre-filter mounted to frame behind fuel tank.
(Posted in: Fuel system 2016)

IMG_2907.JPG
107 hits | 47.3 KB | Posted: 5/20/16
Walbro fuel pump mounted.
(Posted in: Fuel system 2016)

IMG_2908.JPG
106 hits | 49.78 KB | Posted: 5/20/16
Pre-filter mounted.
(Posted in: Fuel system 2016)

IMG_2911.JPG
84 hits | 49.64 KB | Posted: 5/20/16
Heat/splash shield mounted over fuel pump. Pic upside down for some reason.
(Posted in: Fuel system 2016)

IMG_2938.JPG
90 hits | 75.36 KB | Posted: 5/20/16
Y-block on bracket to mount behind cylinder head.
(Posted in: Fuel system 2016)

IMG_2940.JPG
86 hits | 44.3 KB | Posted: 5/20/16
Y-block mounted on head. Pic from below.
(Posted in: Fuel system 2016)

IMG_2941.JPG
78 hits | 51.05 KB | Posted: 5/20/16
Fuel filter mounted and return line connected.
(Posted in: Fuel system 2016)

IMG_2942.JPG
73 hits | 55.5 KB | Posted: 5/20/16
Fuel pump and pre-filter plumbed.
(Posted in: Fuel system 2016)

IMG_2943.JPG
106 hits | 49.76 KB | Posted: 5/20/16
Filter and return.
(Posted in: Fuel system 2016)

IMG_2944.JPG
82 hits | 54.46 KB | Posted: 5/20/16
Fuel pressure regulator on bracket.
(Posted in: Fuel system 2016)

IMG_2945.JPG
95 hits | 68.98 KB | Posted: 5/20/16
Fuel pressure regulator.
(Posted in: Fuel system 2016)

IMG_2998.JPG
107 hits | 53.51 KB | Posted: 5/20/16
Intercooler hiding where the AC condenser used to live.
(Posted in: Intercooler)

IMG_2999.JPG
130 hits | 56.01 KB | Posted: 5/20/16
Intercooler? What intercooler? Shame to hide it all but that's what happens when you build a sleeper.
(Posted in: Intercooler)

IMG_2563.JPG
102 hits | 46.84 KB | Posted: 3/10/16
Cardboard rough draft. Just checking heights and such.
(Posted in: Center console )

IMG_2572.JPG
115 hits | 30.52 KB | Posted: 3/10/16
Drawing out the second version.
(Posted in: Center console )

IMG_2573.JPG
105 hits | 38.15 KB | Posted: 3/10/16
More drawings. Better to find problems on paper then later.
(Posted in: Center console )

IMG_2574.JPG
102 hits | 32.81 KB | Posted: 3/10/16
These are all to scale. Some are 1:1.
(Posted in: Center console )

IMG_2598.JPG
97 hits | 53.3 KB | Posted: 3/10/16
Prototype. Much easier to mock up in styrofoam than in MDF.
(Posted in: Center console )

IMG_2599.JPG
94 hits | 51.88 KB | Posted: 3/10/16
Storage in the arm rest, cup holders, shifter, pull out cup holders for the rear, and temp/volt gauges up front. Oh, and 12 V power and USB power.
(Posted in: Center console )