Fred Willson > 1983 Ford Bronco > open folder Tailgate Support

This the condition of the tail gate support that I found after removing the 1/4 panel. Not good.
Hits: 489
Size: 70.78 KB
Posted: 3/4/11
This the condition of the tail gate support that I found after removing the 1/4 panel. Not good.		BAD
Hits: 432
Size: 77.33 KB
Posted: 3/4/11
BAD
Hits: 444
Size: 72.97 KB
Posted: 3/4/11
See what happens to metal as it rots. It swells and falls apart.
Hits: 458
Size: 73.51 KB
Posted: 3/7/11
See what happens to metal as it rots. It swells and falls apart.
Hits: 395
Size: 64.84 KB
Posted: 3/8/11

Hits: 431
Size: 47.15 KB
Posted: 3/8/11
Welds cut to remove old tail gate support.
Hits: 377
Size: 50.21 KB
Posted: 3/8/11
Welds cut to remove old tail gate support.		Cutting to fit new tail gate support
Hits: 404
Size: 70.15 KB
Posted: 3/8/11
Cutting to fit new tail gate support		Surface cleaned up
Hits: 416
Size: 52.95 KB
Posted: 3/8/11
Surface cleaned up 		Tail gate support removed
Hits: 380
Size: 59.97 KB
Posted: 3/8/11
Tail gate support removed

Hits: 394
Size: 40.62 KB
Posted: 3/8/11

Hits: 393
Size: 62.68 KB
Posted: 3/8/11
Using a flanging tool to prepare for the overlap of the new material.
Hits: 412
Size: 55.56 KB
Posted: 3/8/11
Using a flanging tool to prepare for the overlap of the new material.
Hits: 409
Size: 54.95 KB
Posted: 3/8/11
Liberated tail gate support from a 95 Bronco in the junk yard. I took the back 18 inches of the 95 ...
Hits: 382
Size: 62.86 KB
Posted: 3/8/11
Liberated tail gate support from a 95 Bronco in the junk yard. I took the back 18 inches of the 95 ...

Hits: 433
Size: 81.75 KB
Posted: 3/7/11

Hits: 428
Size: 71.25 KB
Posted: 3/4/11
Tub support and tail gate support in position ready for the marriage.
Hits: 422
Size: 63.69 KB
Posted: 3/8/11
Tub support and tail gate support in position ready for the marriage.
Hits: 381
Size: 61.92 KB
Posted: 3/8/11

Hits: 386
Size: 52.18 KB
Posted: 3/8/11

Hits: 395
Size: 58.55 KB
Posted: 3/8/11

Hits: 415
Size: 65.6 KB
Posted: 3/8/11

Hits: 416
Size: 49.01 KB
Posted: 3/8/11
Holding in place
Hits: 409
Size: 69.43 KB
Posted: 3/8/11
Holding in place 		Holes for blind rivets along with structural epoxy "FUSOR 112B" which has about 30 to 60 m...
Hits: 453
Size: 73.35 KB
Posted: 3/8/11
Holes for blind rivets along with structural epoxy "FUSOR 112B" which has about 30 to 60 m...

Hits: 416
Size: 63.04 KB
Posted: 3/8/11

Hits: 413
Size: 65.34 KB
Posted: 3/8/11

Hits: 383
Size: 76.43 KB
Posted: 3/8/11

Hits: 408
Size: 65.12 KB
Posted: 3/8/11
Just a note: Make sure you have measured the distance from some point on the side of the truck to t...
Hits: 406
Size: 64 KB
Posted: 3/8/11
Just a note: Make sure you have measured the distance from some point on the side of the truck to t...
Note the overlap of the old tub floor and the material I left attached from the donor truck. It is ...
Hits: 394
Size: 70.17 KB
Posted: 3/8/11
Note the overlap of the old tub floor and the material I left attached from the donor truck. It is ...		Ready for the 1/4 panel.
Hits: 406
Size: 55.68 KB
Posted: 3/8/11
Ready for the 1/4 panel.		   
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2026 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog