2006 Suzuki Hayabusa 1300
Owner: SuperMotors SuperMotors Owner    Subscriber        (All of this user's registries on SuperMotors)
From: Minneapolis, MN, U.S.A.        (Other registries in MN)
Year, Make, & Model: 2006 Suzuki Hayabusa 1300        (Other Suzuki Hayabusa 1300s)
Avatar:
Nickname: 'Busa
Mileage:
Engine:
Drivetrain:
Notes:
Last Updated: 9/12/2006
Hits: 28630
Album
Folder Hits Comments Created Updated
folder PPM Custom's Chrome Billet Hayabusa Gauge Bezel150045,89109/12/069/12/06
Newest Media Files
busa13.jpg
3322 hits | 118.49 KB | Posted: 9/12/06

Seen side-by-side, the stock and PPM bezel are quite a contrast. While the stock part’s faux-carbon finish is a bit cheap looking, the PPM part exudes class and quality.

PPM Custom
2222-F Patterson St.
Greensboro, NC 27407
866-511-2453
[url...
busa12.jpg
2641 hits | 78.3 KB | Posted: 9/12/06

Now that the fairings are in place, tighten all three Allen screws.
busa11.jpg
3544 hits | 69.62 KB | Posted: 9/12/06

To install the pins that hold the inner fairing to the windscreen supports you must first reset them so the center is sticking up as shown in the picture. Once in place, just press the center flush to lock the pins.
busa10b.jpg
2630 hits | 77 KB | Posted: 9/12/06

busa10a.jpg
2843 hits | 101.14 KB | Posted: 9/12/06

Next, install the inner fairing. Starting from the rear of the fairing pieces, work your way forward to the windscreen support.

Once both sides are in, install the center Allen screw to hold them in place while you get the other screws started. R...
busa9b.jpg
2764 hits | 100.3 KB | Posted: 9/12/06

busa9a.jpg
2784 hits | 80.96 KB | Posted: 9/12/06

Once the screws are tight, install the new foam weather seal around the bottom and sides of the bezel. It should attach just above the screw heads and the tabs at the corners, and reach around the top far enough to meet the inner fairing near the ed...
busa8.jpg
2677 hits | 90.58 KB | Posted: 9/12/06

To permanently mount the bezel, peel the cover-strips off the double-sided tape on the back of the PPM Custom bezel. The tape will instantly adhere once it touches the gauge cluster, so it’s important to get the position right the first time. Our...
busa7.jpg
4126 hits | 83.13 KB | Posted: 9/12/06

Before mounting the PPM Custom billet bezel with the provided adhesive, set the new part in place to check the fit. It should bow up just a little at the edges but if it won’t center properly you may have a piece of the original mounting tape stil...
Most Viewed Files
busa1b.jpg
4566 hits | 88.55 KB | Posted: 9/12/06

By Arthur Jensen

Blingin' Billet Bezel: We Install a PPM Custom's Chrome Billet 'Busa Gauge Bezel

The Suzuki Hayabusa has made a name for itself as one of the fastest modern production sport bikes in existence, and coincidentally...
busa7.jpg
4126 hits | 83.13 KB | Posted: 9/12/06

Before mounting the PPM Custom billet bezel with the provided adhesive, set the new part in place to check the fit. It should bow up just a little at the edges but if it won’t center properly you may have a piece of the original mounting tape stil...
busa11.jpg
3544 hits | 69.62 KB | Posted: 9/12/06

To install the pins that hold the inner fairing to the windscreen supports you must first reset them so the center is sticking up as shown in the picture. Once in place, just press the center flush to lock the pins.
busa6.jpg
3398 hits | 99.25 KB | Posted: 9/12/06

Since the bezel is still attached by the double-sided tape, you will have to pry it up carefully to avoid damaging the gauge cluster. We were able to get the job done with a flat screwdriver and our fingers working from the left side towards the righ...
busa13.jpg
3322 hits | 118.49 KB | Posted: 9/12/06

Seen side-by-side, the stock and PPM bezel are quite a contrast. While the stock part’s faux-carbon finish is a bit cheap looking, the PPM part exudes class and quality.

PPM Custom
2222-F Patterson St.
Greensboro, NC 27407
866-511-2453
[url...
busa5.jpg
2892 hits | 105.17 KB | Posted: 9/12/06

The stock 'Busa bezel is held on with two Phillips screws along the bottom edge and double sided tape on its back. The screws are located just below the neutral light and are hidden behind the stock foam weather seal.
busa10a.jpg
2843 hits | 101.14 KB | Posted: 9/12/06

Next, install the inner fairing. Starting from the rear of the fairing pieces, work your way forward to the windscreen support.

Once both sides are in, install the center Allen screw to hold them in place while you get the other screws started. R...
busa9a.jpg
2784 hits | 80.96 KB | Posted: 9/12/06

Once the screws are tight, install the new foam weather seal around the bottom and sides of the bezel. It should attach just above the screw heads and the tabs at the corners, and reach around the top far enough to meet the inner fairing near the ed...
busa9b.jpg
2764 hits | 100.3 KB | Posted: 9/12/06

Maintenance & Modification Logs
This user hasn't added any log entries, yet.
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2025 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog