DSCF0036.JPG
1690 hits | 63.8 KB | Posted: 7/7/04
Reinstalling lifters

DSCF0037.JPG
1362 hits | 54.35 KB | Posted: 7/7/04

DSCF0039.JPG
1470 hits | 60.34 KB | Posted: 7/7/04
Lifters installed.

DSCF0040.JPG
1343 hits | 55.68 KB | Posted: 7/7/04
Close-up of bores (getting ready to install head gaskets).

DSCF0043.JPG
1295 hits | 55.8 KB | Posted: 7/7/04

DSCF0044.JPG
1355 hits | 57.26 KB | Posted: 7/7/04
Installing head gaskets.

DSCF0046.JPG
1475 hits | 58.76 KB | Posted: 7/7/04
Not exactly a perfect circle in these gaskets!

DSCF0049.JPG
1320 hits | 59.08 KB | Posted: 7/7/04
Installing newly re-worked heads.

DSCF0050.JPG
1531 hits | 58.26 KB | Posted: 7/7/04
These are not exactly lightweight!

DSCF0051.JPG
1466 hits | 67.5 KB | Posted: 7/27/04
Reinstalling the pushrods

DSCF0052.JPG
1314 hits | 56.62 KB | Posted: 7/27/04
Close-up of the ported exhaust ports

DSCF0053.JPG
1340 hits | 65.78 KB | Posted: 7/27/04
Another view of the newly ported exhaust ports

DSCF0054.JPG
1317 hits | 68.6 KB | Posted: 7/27/04
Removing duct tape from the intake side of the heads to prepare for the intake installation.

DSCF0055.JPG
1289 hits | 64.4 KB | Posted: 7/27/04
More tape removal.

DSCF0059.JPG
1270 hits | 60.38 KB | Posted: 7/27/04
Heads are installed on the 390.

DSCF0060.JPG
1334 hits | 65.76 KB | Posted: 7/27/04
Closer view of the 390 topend.

DSCF0062.JPG
1400 hits | 59.48 KB | Posted: 7/27/04
Close-up of the valve springs. The new exhaust valves have nice straight edges on them (no more mus...

DSCF0063.JPG
1413 hits | 57.09 KB | Posted: 7/27/04
Side view of the topened sans intake.

DSCF0065.JPG
1378 hits | 68.84 KB | Posted: 7/27/04
Torquing the heads to spec.

DSCF0066.JPG
1563 hits | 62.49 KB | Posted: 7/27/04
Fel-Pro gaskets used with a bead of RTV at the corners to prevent oil leaks. NOTE- my 390 burns oil...

DSCF0067.JPG
1448 hits | 63.8 KB | Posted: 7/27/04
Close-up of the RTV at the corner of the gaskets.

DSCF0074.JPG
1472 hits | 70.5 KB | Posted: 7/27/04
Getting ready for the intake install.

DSCF0075.JPG
1382 hits | 65.39 KB | Posted: 7/27/04
All gaskets are installed.

DSCF0069.JPG
1307 hits | 56.26 KB | Posted: 7/27/04
Bottom-side view of the Performer RPM intake that's ready for installation.

DSCF0070.JPG
1371 hits | 71.37 KB | Posted: 7/27/04
Strategically aligning the intake with the water pump.

DSCF0073.JPG
1350 hits | 63.62 KB | Posted: 7/27/04
Intake & carb in place, ready to tighten.

DSCF0072.JPG
1276 hits | 70.17 KB | Posted: 7/27/04
Hand tightening the intake prior to properly torquing with a torque wrench.

DSCF0077.JPG
1319 hits | 58.94 KB | Posted: 7/27/04
Installing valvetrain

DSCF0078.JPG
1328 hits | 70.9 KB | Posted: 7/27/04
Another valvetrain install pic. Too bad I don't have clear valve covers, these look really nice whe...

DSCF0080.JPG
1262 hits | 67.4 KB | Posted: 7/27/04
Hand-tightening the valvetrain prior to proper torquing with a torque wrench.

DSCF0081.JPG
1373 hits | 66.41 KB | Posted: 7/27/04
Another shot of fthe valvetrain installed.

DSCF0082.JPG
1447 hits | 60.55 KB | Posted: 7/27/04
Torquing the valvetrain to spec.

DSCF0083.JPG
1382 hits | 59.68 KB | Posted: 7/27/04
Topened assembled -- ready for distributor.

DSCF0085.JPG
1397 hits | 67.66 KB | Posted: 7/27/04
Close-up of the installed distributor.

DSCF0084.JPG
1438 hits | 59.82 KB | Posted: 7/27/04
Topend ready-to-install.