DSC01747.JPG 610 hits | 61.65 KB | Posted: 10/28/03 3 deep breaths and continue (Posted in: T-Case 10/28/03)
DSC01748.JPG 536 hits | 71.66 KB | Posted: 10/28/03 Plate off.....taking a look around (Posted in: T-Case 10/28/03)
DSC01749.JPG 551 hits | 72.57 KB | Posted: 10/28/03 No chunks of metal....rags....etc.......lots of small parts (Posted in: T-Case 10/28/03)
DSC01750.JPG 578 hits | 49.59 KB | Posted: 10/28/03 Too much excitment for one day, this will be my stopping point for now (Posted in: T-Case 10/28/03)
DSC01751.JPG 588 hits | 52.14 KB | Posted: 10/28/03 Just ordered my Advanced Adapters SYE kit....now I wait and prepare to order my new rear driveshaft (Posted in: T-Case 10/28/03)
DSC01783.JPG 563 hits | 63.5 KB | Posted: 11/23/03 The "gooey" magnetic particle pick-up washer that is full of metal (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01786.JPG 564 hits | 60.71 KB | Posted: 11/23/03 Look at how dirty it is (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01789.JPG 593 hits | 55.25 KB | Posted: 11/23/03 A better look at where the filter and magnet were (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01794.JPG 593 hits | 52.48 KB | Posted: 11/23/03 NASTY!......those are two pieces of plastic that I was never able to figure out where they came from (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01797.JPG 539 hits | 65.68 KB | Posted: 11/23/03 A better look at the "goo" on both the filter and the magnet....the red is from the teeth on my speedo gear (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01799.JPG 593 hits | 70.75 KB | Posted: 11/23/03 Got the chain off with a little "gentle persuation" (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01800.JPG 646 hits | 71.96 KB | Posted: 11/23/03 That is a beefy chain (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01805.JPG 647 hits | 72.95 KB | Posted: 11/23/03 Off it comes (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01806.JPG 585 hits | 71.75 KB | Posted: 11/23/03 The inside without the chain (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01809.JPG 604 hits | 74.89 KB | Posted: 11/23/03 Out it comes, and a big "thank you" to Gee (pictured) who is helping (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01810.JPG 546 hits | 67.28 KB | Posted: 11/23/03 It is big and heavy (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01812.JPG 583 hits | 66.61 KB | Posted: 11/23/03 The case without the rear output shaft (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01820.JPG 584 hits | 44.65 KB | Posted: 11/23/03 The two shafts side by side to demonstrate the difference in length (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01821.JPG 561 hits | 49.72 KB | Posted: 11/23/03 All these gears need to be transfered to the new shaft (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01828.JPG 514 hits | 41.59 KB | Posted: 11/23/03 These two needle bearings need to come out so that the gears will slip onto the new shaft (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01829.JPG 560 hits | 43.01 KB | Posted: 11/23/03 After they come out they will be discarded (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01842.JPG 575 hits | 37.13 KB | Posted: 11/23/03 This PVC pipe is the perfect diameter to do the job (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01844.JPG 554 hits | 47.68 KB | Posted: 11/23/03 There we go, let me get the hammer (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01847.JPG 547 hits | 55.21 KB | Posted: 11/23/03 Just like this......I found a deadblow hammer to work better than this rubber mallet (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01848.JPG 563 hits | 71.1 KB | Posted: 11/23/03 Now they are out (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01853.JPG 615 hits | 52.35 KB | Posted: 11/23/03 Now the gears are on the new shaft (Posted in: SYE/Driveshaft Install 11/22/03)
DSC01854.JPG 595 hits | 51.05 KB | Posted: 11/23/03 A new comparison (Posted in: SYE/Driveshaft Install 11/22/03)
