DSC05185.JPG
594 hits | 79.01 KB | Posted: 9/8/08
Got it up on jackstands today to start fixing some things. It only has 4 degree bushings, and needs ...

DSC05186.JPG
510 hits | 64.1 KB | Posted: 9/8/08
I had already cut the springs to fit the spring cup better, now I cut 1 full coil.

DSC05187.JPG
510 hits | 52.09 KB | Posted: 9/8/08
1 Cut coil

DSC05188.JPG
490 hits | 64.18 KB | Posted: 9/8/08
Installed 7 degree bushing.

DSC05189.JPG
444 hits | 66.13 KB | Posted: 9/8/08
Passenger side as well

DSC05190.JPG
415 hits | 75.08 KB | Posted: 9/8/08
Hard to see in driveway pics, but it is ALOT lower

DSC05192.JPG
489 hits | 83.18 KB | Posted: 9/8/08

DSC05193.JPG
477 hits | 65.03 KB | Posted: 9/8/08

9-10-08 012.jpg
449 hits | 62.88 KB | Posted: 9/9/08
Got my warrantied shafts, so time to put them together with the superjoints

9-10-08 014.jpg
446 hits | 62.98 KB | Posted: 9/9/08
New stub shaft

9-10-08 015.jpg
475 hits | 63.72 KB | Posted: 9/9/08
New short side shaft

9-10-08 016.jpg
438 hits | 61.83 KB | Posted: 9/9/08
Looks different on this end I think

9-10-08 017.jpg
445 hits | 74.04 KB | Posted: 9/9/08
Deburred the bores with a small file

9-10-08 020.jpg
466 hits | 61.95 KB | Posted: 9/9/08
Chamfered side points at the shaft. dont forget the full circle clips

9-10-08 021.jpg
415 hits | 63.6 KB | Posted: 9/9/08
Put together the grease gun

9-10-08 022.jpg
439 hits | 61.54 KB | Posted: 9/9/08
O-rings installed in the caps

9-10-08 023.jpg
477 hits | 70.47 KB | Posted: 9/9/08
Used the grease on all the surfaces

9-10-08 024.jpg
483 hits | 60.55 KB | Posted: 9/9/08
And pushed em in with my HF u-joint tool

9-10-08 025.jpg
498 hits | 51.42 KB | Posted: 9/9/08
Closer look

9-10-08 026.jpg
482 hits | 57.97 KB | Posted: 9/9/08
Stub shaft installed

9-10-08 027.jpg
441 hits | 61.61 KB | Posted: 9/9/08
Grease fittings installed, then pumped in grease till i felt resistance

9-10-08 028.jpg
500 hits | 75.48 KB | Posted: 9/9/08
Ready to go in

9-10-08 029.jpg
535 hits | 72.75 KB | Posted: 9/9/08

9-10-08 033.jpg
521 hits | 64.47 KB | Posted: 9/10/08
Dust shield installed

9-10-08 034.jpg
510 hits | 62.27 KB | Posted: 9/10/08
And lil plastic thingy

9-10-08 036.jpg
470 hits | 70.98 KB | Posted: 9/10/08
Taking apart the passenger side, so I can put the superjoint into the yukon shafts.

9-10-08 038.jpg
474 hits | 71.86 KB | Posted: 9/10/08
Spindles still looks shiny

9-10-08 039.jpg
446 hits | 69.79 KB | Posted: 9/10/08
Lots of room to install shafts

9-10-08 040.jpg
480 hits | 60.44 KB | Posted: 9/10/08
Long side assembled

9-10-08 042.jpg
484 hits | 81.22 KB | Posted: 9/10/08
Ready to install

9-10-08 045.jpg
486 hits | 60.49 KB | Posted: 9/10/08
Beefy

9-10-08 046.jpg
465 hits | 56.52 KB | Posted: 9/10/08

9-10-08 050.jpg
453 hits | 79.28 KB | Posted: 9/10/08
Track bar is out to be shortened by an inch, and the gear cover is getting machined so it will stop ...

9-10-08 052.jpg
474 hits | 59.23 KB | Posted: 9/11/08
Seal surface of the Bluetorch cover cleaned up

9-10-08 053.jpg
468 hits | 85.74 KB | Posted: 9/11/08
Track bar back in, and axle centered.

9-10-08 056.jpg
457 hits | 84.46 KB | Posted: 9/12/08
Drives much better. I did a walk around to get some pics with the cut coils

9-10-08 057.jpg
472 hits | 82.64 KB | Posted: 9/12/08

9-10-08 058.jpg
496 hits | 80.42 KB | Posted: 9/12/08

9-10-08 059.jpg
505 hits | 76.69 KB | Posted: 9/12/08

9-10-08 060.jpg
536 hits | 78.99 KB | Posted: 9/12/08