Steve83 > 1994 Ford Crown Victoria > open folder Forced Lube

Before. Tailhousing bushings are prone to wear because they are only lubricated by the splash of fl...
Hits: 3251
Size: 54.41 KB
Posted: 4/17/05
Before. Tailhousing bushings are prone to wear because they are only lubricated by the splash of fl...		Tailhousing removed. With the transmission tilted up, no fluid was lost, and the gasket remained in...
Hits: 3522
Size: 56.51 KB
Posted: 4/17/05
Tailhousing removed. With the transmission tilted up, no fluid was lost, and the gasket remained in...		The LINE port is at the back of the bellhousing on the L side.
Hits: 2979
Size: 63.55 KB
Posted: 4/17/05
The LINE port is at the back of the bellhousing on the L side.		The tip of the driveshaft slip yoke is reduced, so it appears loose in the bushing. The green pla...
Hits: 2976
Size: 40.31 KB
Posted: 4/17/05
The tip of the driveshaft slip yoke is reduced, so it appears loose in the bushing. The green pla...		If your gasket has to be replace (I reused mine), buy F7AZ-7086-A $3.16 at the dealership.
Hits: 2827
Size: 53.32 KB
Posted: 4/17/05
If your gasket has to be replace (I reused mine), buy F7AZ-7086-A $3.16 at the dealership.
The TCCoA article recommends an 18" tube, but this 20" one is obviously short. I used a 30" line.
Hits: 2737
Size: 38.56 KB
Posted: 4/17/05
The TCCoA article recommends an 18" tube, but this 20" one is obviously short. I used a 30" line.		I drilled too far forward - I should have drilled in the dimple of the casting. Considering the rot...
Hits: 2717
Size: 46.91 KB
Posted: 4/17/05
I drilled too far forward - I should have drilled in the dimple of the casting. Considering the rot...		I almost missed the bushing.
Hits: 2866
Size: 51.75 KB
Posted: 4/17/05
I almost missed the bushing.		After drilling, tapping, grinding, & sanding, I rinsed the tailhousing thoroughly with carb cleaner ...
Hits: 2586
Size: 43.23 KB
Posted: 4/17/05
After drilling, tapping, grinding, & sanding, I rinsed the tailhousing thoroughly with carb cleaner ...		Finished Side
Hits: 2426
Size: 39.79 KB
Posted: 4/17/05
Finished Side
Finished Top
Hits: 2294
Size: 41.88 KB
Posted: 4/17/05
Finished Top		Finished Rear
Hits: 2541
Size: 75.09 KB
Posted: 4/17/05
Finished Rear		Finished installed in the tunnel
Hits: 2335
Size: 53.14 KB
Posted: 4/17/05
Finished installed in the tunnel		Finished installed view of the shifter. There is no interference.
Hits: 2365
Size: 46.18 KB
Posted: 4/17/05
Finished installed view of the shifter. There is no interference.		Finished installed view of the shifter from below. There is no interference.
Hits: 2368
Size: 68.09 KB
Posted: 4/17/05
Finished installed view of the shifter from below. There is no interference.
Fluid leaks out of the slip-yoke's vent hole in the center behind the U-joint, and drips off the bot...
Hits: 3938
Size: 42.51 KB
Posted: 5/16/05
Fluid leaks out of the slip-yoke's vent hole in the center behind the U-joint, and drips off the bot...		Since I couldn't really seal the vent hole with the U-joint in place, I just made a bridge of sealan...
Hits: 2578
Size: 32.35 KB
Posted: 5/16/05
Since I couldn't really seal the vent hole with the U-joint in place, I just made a bridge of sealan...		After a few hundred miles, I dropped the pan, changed the filter & gasket (it was leaking), and adde...
Hits: 5304
Size: 72.18 KB
Posted: 6/2/05
After a few hundred miles, I dropped the pan, changed the filter & gasket (it was leaking), and adde...		  
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2025 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog