pic1.jpg
2262 hits | 67.01 KB | Posted: 10/2/05
The old 14 inch wheels before the install. Nice, but they won't work with the big 13 inch Baer roto...

pic2.jpg
4125 hits | 59.17 KB | Posted: 10/2/05
17x7 Cragar S/S on the front with 4 inch backspace and 225/40 Nitto tires. No clearance problems wi...

pic3.jpg
2420 hits | 60.57 KB | Posted: 10/2/05
13 inch rotors on the front and 12 inch rotors on the rear. Awesome!

pic4.jpg
2039 hits | 86.33 KB | Posted: 10/2/05
The old, single reservoir, master cylinder. Thank you Lord that it never failed on me during all th...

pic5.jpg
2225 hits | 80.3 KB | Posted: 10/2/05
The new master cylinder. It puts the brake lines a bit close to the valve covers, because the ports...

pic5a.jpg
1853 hits | 69.74 KB | Posted: 10/3/05
Proportion valve, located on the right side of the engine bay (from the driver's seat point of view)...

pic1a.jpg
1676 hits | 61.62 KB | Posted: 10/3/05
Old front drum. Good bye sluggish brakes.

pic1b.jpg
1708 hits | 68.46 KB | Posted: 10/3/05
Down to the spindle. You can see the old hub in the blue tub.

pic1c.jpg
1659 hits | 68.09 KB | Posted: 10/3/05
The Baer hub and caliper bracket which will go on the front spindle.

pic1d.jpg
1682 hits | 73.8 KB | Posted: 10/3/05
Baer caliper bracket is installed on the front spindle.

pic1e.jpg
1758 hits | 70.69 KB | Posted: 10/3/05
Baer hub installed on the front spindle.

pic6a.jpg
1618 hits | 65.61 KB | Posted: 10/3/05
Front 13 inch rotor and caliper. Front kit part# is 4261029. Master cylinder comes with the kit.

pic6.jpg
1801 hits | 72.23 KB | Posted: 10/3/05
Parts and pieces. All for the rear end, except for the master cylinder and proportion valve, of cou...

pic7.jpg
2147 hits | 59.94 KB | Posted: 10/3/05
Old rear wheel and tire. Duffee Motorsports works on alot of Fords.

pic7a.jpg
1591 hits | 56.44 KB | Posted: 10/3/05
Old rear drum. They were noisey. Despite my maintenence. Bye Bye.

pic8.jpg
1659 hits | 59.07 KB | Posted: 10/3/05
Down to the rear axle housing.

pic8a.jpg
1652 hits | 60.96 KB | Posted: 10/3/05
Baer clamp installed to hold the new brake line.

pic8b.jpg
1733 hits | 64.41 KB | Posted: 10/3/05
New brake line on.

pic8c.jpg
1718 hits | 63.72 KB | Posted: 10/3/05
Assembly continues. Baer bracket for the caliper is on and the axle is in.

pic9.jpg
2033 hits | 58.45 KB | Posted: 10/3/05
Rear 12 inch rotor and caliper installed.

pic9a.jpg
1886 hits | 60.11 KB | Posted: 10/3/05
A look at the back side of the rear rotor. Note: new mounting tabs had to be welded on to each rear...

pic10.jpg
3378 hits | 76.81 KB | Posted: 10/3/05
17x9 Cragar S/S wheels on the rear with 5 inch backspace and 255/40 Nitto tires.

pic7b.jpg
1725 hits | 74.24 KB | Posted: 10/3/05
The axle flange had to be machined in order for the rear rotor to fit over it.

pic7c.jpg
1714 hits | 49.42 KB | Posted: 10/3/05
You can see the shiny new surface where the axle flange was machined.