Donzi
 |
|
• New Orleans, LA, USA |
|
• Registered on 6/7/2003 |
|
• 259 posts |
|
|
|
 Posted:11/6/2003 22:07 |
|
|
|
Josh, anything worth getting??? Any D60 14ff combo's for 100.00 and bucket of KFC??? |
|
Bowtie Blazer
 |
|
• Baton Rouge, LA, USA |
|
• Registered on 5/27/2003 |
|
• 1,220 posts |
|
|
|
|
Posted:11/6/2003 23:53 |
|
|
just 14ff $100 is what he told me
 |
|
Donzi
|
|
• New Orleans, LA, USA |
|
• Registered on 6/7/2003 |
|
• 259 posts |
|
|
|
|
Posted:11/7/2003 12:50 |
|
|
|
Josh, is this a 4.10?? If not ,no biggie I guess since you can remove the entire pinion set. I am going to take a trip up this weekend to get it. |
|
Bowtie Blazer
|
|
• Baton Rouge, LA, USA |
|
• Registered on 5/27/2003 |
|
• 1,220 posts |
|
|
|
|
Posted:11/7/2003 13:29 |
|
|
I still couldn't tell you for sure as it rotated freely but still had a rear driveshaft connected....4.10 was the most common ratio in these axles as they were in 3/4 and one ton trucks, usually used to haul trailers and weight in general so they were geared lower....3.73 is also avalible and 4.56 is rare but not always unusual, could have a gov lock in it as well in which case if you want to weld up the spider's we'll trade axles and i'll keep the gov lock, works alot like a detroit, Kris has one in his 10 bolt......I searched the truck for glovebox codes etc with no luck....I bet its 4.10's I'll post directions and a makeshift map of where the truck lies in the yard, its completely intact so you'll need tools to unbolt the driveshaft, and u-bolts, doesn't look very rusty so they may come right off....brakes look as if they might work as well...
|
|
Herbert Vining Jr
 |
|
• Patterson, LA, USA |
|
• Registered on 11/19/2002 |
|
• 296 posts |
|
|
|
|
Posted:11/7/2003 14:26 |
|
|
I'm needing some front fenders and the driver's side headlight bezel for the bronco, I don't care what truck it is on, Bronco-F 150 250 350, as long as it's 80-86, and has no severe rust, if any of you go yarding and see any pls ask how much they'd want for all three, I'm on a $100 budget for that, mainly need the drivers side fender or if any of you know where I can get a towbar instead for $100 or under for me to pull the bronco with, any assistance would be greatly appreciated, just give me a number and address and I'll grab my tools and go to the yard, the yards around here are lame
1980 Bronco (Big Bertha / The Beast) 351M/C6/NP208/D44/9"/33's
My Bronco Site |
|
Wildman
 |
|
• Meraux, LA, USA |
|
• Registered on 8/15/2003 |
|
• 301 posts |
|
|
|
|
Posted:11/7/2003 17:11 |
|
|
| Quote: | | I'm needing some front fenders and the driver's side headlight bezel for the bronco, I don't care what truck it is on, Bronco-F 150 250 350, as long as it's 80-86, and has no severe rust, if any of you go yarding and see any pls ask how much they'd want for all three, I'm on a $100 budget for that, mainly need the drivers side fender or if any of you know where I can get a towbar instead for $100 or under for me to pull the bronco with, any assistance would be greatly appreciated, just give me a number and address and I'll grab my tools and go to the yard, the yards around here are lame |
You might want to try Certi-fit corp. in Metairie, you could probably get a new fender for around $50 brand new.
 |
|
Bowtie Blazer
|
|
• Baton Rouge, LA, USA |
|
• Registered on 5/27/2003 |
|
• 1,220 posts |
|
|
|
|
Posted:11/7/2003 17:28 |
|
|
if not they are all over the yards around here...as for tow bar you need to think higher than $100 for one....the cheap ones are 100 and only rated for 3500lbs you need a 5500 lb one...keep in mind your truck weighs atleast 5600lbs
|
|
schmuck
 |
|
• nola, XX, USA |
|
• Registered on 5/21/2003 |
|
• 1,187 posts |
• 1
|
|
|
Posted:11/7/2003 17:29 |
|
|
wildman is right certafit is cheap and i think home depot sells tow bars for about $90
nucking futs
|
|
Wildman
|
|
• Meraux, LA, USA |
|
• Registered on 8/15/2003 |
|
• 301 posts |
|
|
|
|
Posted:11/7/2003 17:33 |
|
|
I BOUGHT A NEW HOOD, GRILL, FRONT BUMPER, AND A TAILGATE FROM THEM ALREADY.  cap L on The quality seams to be there also. My Dakota looks new.
|
|
Herbert Vining Jr
|
|
• Patterson, LA, USA |
|
• Registered on 11/19/2002 |
|
• 296 posts |
|
|
|
|
Posted:11/7/2003 18:04 |
|
|
thanks for the info guys, I'll check them out tuesday. and I might check ebay for a two bar, however my I kinda need my fenders more so I'll get them first
P.S. It's frickin cold up here!!!
1980 Bronco (Big Bertha / The Beast) 351M/C6/NP208/D44/9"/33's
My Bronco Site |
|