HPIM0063.JPG
621 hits | 69.28 KB | Posted: 2007-04-14
FMS cam sprocket before machining...
(Posted in: Ford 545ci engine build)

HPIM0063.JPG
540 hits | 69.28 KB | Posted: 2007-04-14
FMS cam sprocket before machining...
(Posted in: Ford 545ci engine build)

magnumpaint.jpg
1620 hits | 66.58 KB | Posted: 2007-01-11
After the first day of installation, the black paint in the center of the wheel started flaking off...alot. The other 3 wheels have this problem, just not as bad as this wheel. Piss poor quality....
(Posted in: Magnum 500 wheels)

HPIM0723.JPG
625 hits | 90.88 KB | Posted: 2006-11-13
Hooking up all the sensors-ran out of time, so after 3pulls and 6k rpm limit, with no changes, 641ft lbs torque, 656 hp. the hp was still climing at 6k. ...
(Posted in: Ford 545ci engine build)

HPIM0727.MPG
683 hits | 6.21 MB | Posted: 2006-11-13
On the SuperFlow 902 dyno, warming up before the 1st pull...
(Posted in: Ford 545ci engine build)

HPIM0711.JPG
549 hits | 120.02 KB | Posted: 2006-11-13
Loaded and ready to take the 545 to the dyno...
(Posted in: Ford 545ci engine build)

HPIM0679.JPG
617 hits | 72.68 KB | Posted: 2006-09-24
My Phantom II gauges were working fine until the elec temp gauge quit!...
(Posted in: Ford 545ci engine build)

HPIM0678.MPG
804 hits | 36.94 MB | Posted: 2006-09-24
A LARGE, crappy quality video file (taken with my digital camera) of the initial start-up of my 545 on the test stand....
(Posted in: Ford 545ci engine build)

HPIM0677.JPG
600 hits | 89.18 KB | Posted: 2006-09-24
Battery, MSD Digital6, wires going to MSD dist., +/- battery wires, alt wire from alt to battery....
(Posted in: Ford 545ci engine build)

HPIM0676.JPG
461 hits | 97.91 KB | Posted: 2006-09-24
test stand...
(Posted in: Ford 545ci engine build)

HPIM0675.JPG
471 hits | 104.25 KB | Posted: 2006-09-24
My thrown-together, homemade test stand!...
(Posted in: Ford 545ci engine build)

HPIM0671.JPG
387 hits | 83.63 KB | Posted: 2006-09-24
Had to fab a brace to steady the A/C adjust pulley, in preperation to running the WP on my homemade engine test stand....
(Posted in: Ford 545ci engine build)

HPIM0664.JPG
385 hits | 71.9 KB | Posted: 2006-09-24
Here's a typical piece of slag hanging in the header tube. This requires grinding flat....
(Posted in: Ford 545ci engine build)

HPIM0580.JPG
445 hits | 87.31 KB | Posted: 2006-09-24
Crites headers clear the Canton pan....
(Posted in: Ford 545ci engine build)

HPIM0589.JPG
384 hits | 80.65 KB | Posted: 2006-09-24
Not much finger room here for tightning header bolts....
(Posted in: Ford 545ci engine build)

HPIM0584.JPG
461 hits | 79.03 KB | Posted: 2006-09-24
Passenger side pipes...
(Posted in: Ford 545ci engine build)