Member Gallery Search Results
 Showing 1 - 22 of 22 files.Pages: 1 
IDThumbnailCaptionModelCommentsHitsUpdated
Prepped.jpg
76 hits | 38.47 KB | Posted: 3/19/24

New Tailgate Shell Prep
IF THE IMAGE IS TOO SMALL, click it.

New shells (which all come from the same Taiwanese factory, so don't pay more to get one from any particular supplier) don't have holes for the swingaway spare, inside carpet ('94-96 on...
(Posted in: Tailgate Tech)
SwingawayPad.jpg
82 hits | 59.75 KB | Posted: 3/21/24

Swingaway Bump Pad
IF THE IMAGE IS TOO SMALL, click it.

Rather than drilling holes in a replacement tailgate to keep the original pad in-place, UHMWPE or [url=https://www.amazon.com/dp/B00823JFM6]PTFE ...
(Posted in: Tailgate Tech)
LatchClean.jpg
36 hits | 43.55 KB | Posted: 3/26/24

Tailgate (or Door) Latch Cleaning
IF THE IMAGE IS TOO SMALL, click it.

Latches that have not been properly maintained may need deep cleaning to restore proper operation. Soak in solvent (naphtha, kerosene, or deodorized mineral spirits - NOT gas ...
(Posted in: Tailgate Tech)
DrumPads.jpg
34 hits | 33.06 KB | Posted: 3/25/24

Drum Shoe Pads
IF THE IMAGE IS TOO SMALL, click it.

An often overlooked area that requires servicing is the backing plate pads that support the brake shoes. The brake shoe shown in the illustration has three tabs. The shoe is pulled against the back...
(Posted in: Brakes & Hubs)
SpeakerTerminals.jpg
34 hits | 58.13 KB | Posted: 3/24/24

Speaker Terminals
IF THE IMAGE IS TOO SMALL, click it.

Instead of splicing aftermarket wires or terminals onto the truck harness, soldering the old original speakers connectors onto the new replacement speakers makes more sense.
(Posted in: Radio)
3BodyMts.jpg
14 hits | 44.07 KB | Posted: 3/28/24

A quick way to check body mounts is to mark the lower isolator & then try to turn it by hand. If it spins, the upper is collapsed, or there's some other problem (rust, collision damage, etc.).
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Body Mounts)
89BXLT-bodymt4.jpg
8 hits | 87.16 KB | Posted: 3/28/24

Even fully-assembled, it's easy to put these vise-grips on the upper core support shell so that the bolt can be unscrewed from it.
IF THE IMAGE IS TOO SMALL, click it.
(Posted in: Body Mounts)
93F250CoreSpt.jpg
9 hits | 63.22 KB | Posted: 3/28/24

After removing the nut from the top (core support mount ONLY), remove the bolt from below.
IF THE IMAGE IS TOO SMALL, click it.

[url=https://www.supermotors.net/registry/media/194329][img]https://www.supermotors.net/getfile/194329/thumbnail/body-mou...
(Posted in: Body Mounts)
FramePatch87B.jpg
8 hits | 80.11 KB | Posted: 3/28/24

Body Mount Frame Repair
IF THE IMAGE IS TOO SMALL, click it.

This frame had rusted away so badly that common frame-savers weren't big enough. I had to get custom patches made locally to weld in. Fortunately, it's not very difficult to separate th...
(Posted in: Body Mounts)
Tilting.jpg
7 hits | 82.96 KB | Posted: 3/28/24

Body Mount Access
IF THE IMAGE IS TOO SMALL, click it.

In most cases, the easiest way to change the body mounts is to remove the bolts along one frame rail, loosen the others, and then lift one side to swap its upper isolators & shells. Then repl...
(Posted in: Body Mounts)
95BEBcorespt3.jpg
9 hits | 54.6 KB | Posted: 3/28/24

Before lifting or tilting a Bronco body, remember to unattach the filler neck by removing these 3 screws, and sliding off the outermost hose clamp under the body.
(Posted in: Body Mounts)
20 ft rebar and 2x4.jpg
24 hits | 94.18 KB | Posted: 3/23/24

(Posted in: Misc)
11-2008 Digital Pics of Scrapbook 9.3 431.JPG
6 hits | 53.4 KB | Posted: 3/28/24

Playing in the mud
(Posted in: New)
Gas Chardon Oil1.jpg
38 hits | 99.92 KB | Posted: 3/24/24

Getting Gas at Chardon Oil in Painesville Ohio. I'm filling up with e-0 (ethanol free, pure gas) Today it was $4.89 a gal. usually about 93 Octane. March 24, 2024, Palm Sunday, temp about 40* f. dry roads.
(Posted in: Photos)
Slider97F250hD.jpg
35 hits | 83.59 KB | Posted: 3/23/24

Rear Window Slider
IF THE IMAGE IS TOO SMALL, click it.

I've had this window for over a year, but I just got around to swapping it in. Silicone grease on the body & gasket lips make installation easier, and prevents leaks by allowing the rubber t...
(Posted in: Big Red)
20240327_143031.jpg
4 hits | 38.95 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_143038.jpg
6 hits | 44.14 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_143046.jpg
8 hits | 79.43 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_143111.jpg
8 hits | 64.02 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_143117.jpg
10 hits | 79.82 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_145116.jpg
10 hits | 122.35 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
20240327_145143.jpg
12 hits | 126.35 KB | Posted: 3/27/24

(Posted in: Illuminated side sill plates H461SFN200)
 Showing 1 - 22 of 22 files.Pages: 1 
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog