PA200009.JPG
375 hits | 88.6 KB | Posted: 3/4/08
doner Dana 44 (76) after rinsing with water

PA210014.JPG
245 hits | 97.03 KB | Posted: 3/4/08
After drying gave it a quick paint job

PA210013.JPG
251 hits | 106 KB | Posted: 3/4/08

P2190003.JPG
234 hits | 79.47 KB | Posted: 3/4/08
Pro Comp 12" travel resevor shocks

P3020002.JPG
272 hits | 80.13 KB | Posted: 3/4/08
These are parts for the Dana 44 rebuild. All seals being replaced, inner spendle bearings, outer pin...

P2290003.JPG
234 hits | 69.43 KB | Posted: 3/4/08
Detroit/Eaton Truetrac installed. Also have one in the rear.

P2290004.JPG
232 hits | 89.76 KB | Posted: 3/4/08
Axles cleaned and painted with Brute U-joints installed.

P2290010.JPG
219 hits | 92.56 KB | Posted: 3/4/08
Just a pic during the rebuild as its being put together.

P3020012.JPG
207 hits | 77.96 KB | Posted: 3/4/08
Otter fully assembled, useing the spicer lockouts. I feel they are stronger than aftermarket(all ste...

P2290008.JPG
188 hits | 91.66 KB | Posted: 3/4/08
Differential fully assembeled and cover installed. Notice the mess, decided to wait untill I was fin...

P3020006.JPG
218 hits | 82.01 KB | Posted: 3/4/08
Axle fully assembled with the new 7* C-bushings.

P3020017.JPG
223 hits | 89.12 KB | Posted: 3/4/08

P3030004.JPG
219 hits | 74.35 KB | Posted: 3/4/08
New Steering. useing steering from a 1990 F350 4X4. Note I will have to trim about .25" of the long ...

P3030005.JPG
236 hits | 85.07 KB | Posted: 3/4/08
Lower draglink (tierod) installed. Note I had to use .25" warshers on top of the knuckles for the t...

PB080007.JPG
239 hits | 93.03 KB | Posted: 3/4/08
Detroit/Eaton Truetrac thats going in the rear 9 inch, 31 spline.

P3020018.JPG
248 hits | 79.28 KB | Posted: 3/4/08
This is the best helper in the word!!

P2240002.JPG
223 hits | 69.31 KB | Posted: 3/4/08
A few pics of my helper working on the 9 inch, getting ready to install gears and locker.

P2240005.JPG
215 hits | 79.26 KB | Posted: 3/4/08
For all those that think installing gears/locker is over there head, he just turned 7!!

P2240003.JPG
269 hits | 63.64 KB | Posted: 3/4/08
Got a nut stuck in the socket, but thats ok, the 7 year old knows what to do and look how well he fi...

P2240016.JPG
274 hits | 67.86 KB | Posted: 3/4/08
Pressing bearings on the Rear Detroit.

P2240014.JPG
258 hits | 68.11 KB | Posted: 3/4/08

P2240019.JPG
243 hits | 71.53 KB | Posted: 3/4/08

P2240008.JPG
419 hits | 79.29 KB | Posted: 3/4/08
Just a pic of how I have everything tucked as high as possable with out a body lift.

P2240013.JPG
274 hits | 86.09 KB | Posted: 3/4/08
The NP205 only hangs down below the frame 2". I dont have the side brace mounted in this picture.

P3060001.JPG
229 hits | 47.77 KB | Posted: 3/6/08
Diffrence in F150 (old) and F350 (new) about .25" longer and the widest part of the tapered shank is...

P3060002.JPG
238 hits | 50.13 KB | Posted: 3/6/08

P3060003.JPG
227 hits | 50.03 KB | Posted: 3/6/08

P3060004.JPG
233 hits | 50.68 KB | Posted: 3/6/08

P3060005.JPG
292 hits | 79.64 KB | Posted: 3/6/08
Added .25" thick warsher on top so that the shank of the tie-rod would seat properly.

P3060006.JPG
255 hits | 67.4 KB | Posted: 3/6/08

P3060007.JPG
259 hits | 86.19 KB | Posted: 3/6/08

P3150020.JPG
261 hits | 76.1 KB | Posted: 3/17/08
Superflex deaver coils, 4" lift for 70's F series

P3150024.JPG
252 hits | 60.54 KB | Posted: 3/17/08
They measure almost 24"

P3130013.JPG
225 hits | 63.1 KB | Posted: 3/17/08
New brake lines

P3130014.JPG
224 hits | 84.09 KB | Posted: 3/17/08
New lines installed with new bleaders for the calibers.

P3130015.JPG
229 hits | 86.77 KB | Posted: 3/17/08
new lines

P3130016.JPG
217 hits | 84.84 KB | Posted: 3/17/08
New brake lines and calibers installed.

P3160025.JPG
211 hits | 83.12 KB | Posted: 3/17/08
coil cups installed with coils in place.

P3160034.JPG
212 hits | 97.44 KB | Posted: 3/17/08
The coils are leaning when in the proper place, may have to make wedges for the lower retainer to ke...

P3160031.JPG
203 hits | 68.19 KB | Posted: 3/17/08
This is how much was trimed from the F350 steering lower tie-rod and sleeve. About 3/8"

P3160033.JPG
215 hits | 67.55 KB | Posted: 3/17/08
where it was trimed from the sleeve. Also I trimed the long tie-rod.

P3160038.JPG
220 hits | 68.84 KB | Posted: 3/17/08
mock up of the shocks, pro-comp 2.0 series with 12" travel

P3160040.JPG
234 hits | 84.36 KB | Posted: 3/17/08

P3170045.JPG
243 hits | 97.85 KB | Posted: 3/17/08
A quick cleaning and paint job for the 9" anfet locker and gear install.

P3170048.JPG
259 hits | 78.23 KB | Posted: 3/17/08

P3190010.JPG
494 hits | 85.14 KB | Posted: 3/19/08
I made this bracket to hold the brake line back a little further than the stock position. A few peop...

P3190014.JPG
248 hits | 90.99 KB | Posted: 3/19/08
I split a vacum hose and placed it around the brake line and then split a heater hose line to go ove...

P3190011.JPG
217 hits | 70.87 KB | Posted: 3/19/08
I also used some vacum line to insulate the brake line here. Nice and snug and should keep from any ...

P3190015.JPG
257 hits | 69.51 KB | Posted: 3/19/08

P3190012.JPG
238 hits | 81.5 KB | Posted: 3/19/08
Just a picture showing it all at once for anyone that doesnt understand what I'm talking about.

P3180005.JPG
255 hits | 72.54 KB | Posted: 3/19/08
Pic of the bracket I made to hold the line

P3200002.JPG
269 hits | 54.36 KB | Posted: 3/20/08

P3200006.JPG
352 hits | 58.95 KB | Posted: 3/20/08

P4210002.JPG
258 hits | 112.82 KB | Posted: 4/21/08
TTB gone!

P4210009.JPG
228 hits | 97.29 KB | Posted: 4/21/08
How I got the rivets out of the coil buckets.

P4210011.JPG
228 hits | 75.54 KB | Posted: 4/21/08
Cleaned up the frame and painted it.

P4210008.JPG
239 hits | 79.45 KB | Posted: 4/21/08

P4210012.JPG
225 hits | 63.76 KB | Posted: 4/21/08
Coil buckets mounted about 1.5" forward.

P4210014.JPG
234 hits | 70.82 KB | Posted: 4/21/08
Only 3 bolts on this side. I will probley but the bottom one in when I fix the steering box but I co...

P4210015.JPG
234 hits | 54.99 KB | Posted: 4/21/08
Had to trim the bottom of the bucket on the drivers side because the frame has a plate on it to rein...

P4210017.JPG
224 hits | 99.61 KB | Posted: 4/21/08
gettin closer.

P4210020.JPG
231 hits | 88.61 KB | Posted: 4/21/08

P4210021.JPG
222 hits | 95.94 KB | Posted: 4/21/08

P4210022.JPG
221 hits | 96.02 KB | Posted: 4/21/08

P4220004.JPG
238 hits | 75.26 KB | Posted: 4/22/08
On its own weight

P4220006.JPG
258 hits | 77.94 KB | Posted: 4/22/08
I cut and laid the brackets back for a better angle on the bushings.

P4220009.JPG
583 hits | 91.14 KB | Posted: 4/22/08
Its about 6" of lift in the front now. FYI, I used 4" superflex coils for a 78/79 Bronko and also us...

P4220010.JPG
363 hits | 78.11 KB | Posted: 4/22/08

P4220011.JPG
459 hits | 73.54 KB | Posted: 4/22/08

P4220012.JPG
314 hits | 64.4 KB | Posted: 4/22/08

P4220013.JPG
249 hits | 78.38 KB | Posted: 4/22/08

P4220014.JPG
258 hits | 90.86 KB | Posted: 4/22/08

P4230009.JPG
235 hits | 84.43 KB | Posted: 4/23/08
Looking at my trac bar and drag link angle. The trac bar mount has not been made yet.

P4230010.JPG
286 hits | 81 KB | Posted: 4/23/08

P4230011.JPG
263 hits | 69.95 KB | Posted: 4/23/08
Just a picture of the radius arm angle, 6.5*.

P4230012.JPG
279 hits | 72.1 KB | Posted: 4/23/08

P5170052.JPG
277 hits | 113.26 KB | Posted: 5/17/08
first trip w/new front axle, nothing special. Just took it up to the farm, about a 100 mile round tr...

P5170053.JPG
455 hits | 111.39 KB | Posted: 5/17/08

P5170054.JPG
428 hits | 94.18 KB | Posted: 5/17/08
Upper Trac Bar mount. It bolts to the frame.

P5170055.JPG
429 hits | 96.51 KB | Posted: 5/17/08

P5170056.JPG
459 hits | 74.52 KB | Posted: 5/17/08
These pro comp shocks are awsome!! Thay tamed these super flex coils!! A very smoth ride on the road...

P5170057.JPG
403 hits | 113.47 KB | Posted: 5/17/08

P5170058.JPG
442 hits | 112.7 KB | Posted: 5/17/08

P5170059.JPG
444 hits | 92.31 KB | Posted: 5/17/08

P5170060.JPG
363 hits | 69.13 KB | Posted: 5/17/08

Beast 5-15-08 2.JPG
434 hits | 91.59 KB | Posted: 5/17/08