bronco 014.jpg
137 hits | 55.93 KB | Posted: 3/12/06
This is what I have so far. It started with a piece of 2x6. I tappered the ends for maximum clearanc...

bronco 015.jpg
91 hits | 49.59 KB | Posted: 3/12/06
rear shot of reciever. I gusetted it with 1/4" plate for extra strength.

bronco 016.jpg
91 hits | 35.48 KB | Posted: 3/12/06
Rock stomper pivot hinge. I plug welded it on the bottom for extra strength.

bronco 017.jpg
110 hits | 73.23 KB | Posted: 3/12/06
This is the latch I'm going to use for the tire carrier. It's made by DE-STA-CO and rated for 700lbs...

bronco 018.jpg
109 hits | 49.55 KB | Posted: 3/12/06
I'm also going to weld these shackle mounts on. The brackets that mount to the frame will go all the...

bronco 027.jpg
92 hits | 56.55 KB | Posted: 3/27/06
Brackets installed and welded up.

bronco 028.jpg
99 hits | 51.75 KB | Posted: 3/27/06

bronco 030.jpg
99 hits | 54.5 KB | Posted: 3/27/06
This picture shows the plug welds through the front of the bumper for the brackets

bronco 029.jpg
89 hits | 50.12 KB | Posted: 3/27/06

bronco 031.jpg
102 hits | 62.62 KB | Posted: 3/27/06
After paint. I used some hamered paint for a textured finish.

bronco 032.jpg
123 hits | 47.99 KB | Posted: 3/27/06
Bumper painted and installed

bronco 033.jpg
133 hits | 46.36 KB | Posted: 3/27/06
In this pic you can see the sheetmetal that was trimed off.

bronco 034.jpg
118 hits | 33.13 KB | Posted: 3/27/06
Close up of trimed sheet metal and brackets

bronco 049.jpg
151 hits | 63.43 KB | Posted: 4/8/06
Rear tire carrier with tire and high lift jack mounted up. I still need to mount the jerry can on th...

bronco 056.jpg
127 hits | 63.71 KB | Posted: 4/8/06

bronco 050.jpg
84 hits | 66.25 KB | Posted: 4/8/06

bronco 057.jpg
119 hits | 76.15 KB | Posted: 4/8/06
Close up of wheel locks and wing nut with pad lock for extra security.

bronco 048.jpg
131 hits | 75.1 KB | Posted: 4/8/06
Backside of tire carrier. Gusseted with 3/16 sheet metal at critical areas.

bronco 046.jpg
98 hits | 98.77 KB | Posted: 4/8/06

bronco 047.jpg
95 hits | 41.6 KB | Posted: 4/8/06
I added a 1/2" block for the tire carrier to rest on when it's closed.

bronco 059.jpg
80 hits | 47.64 KB | Posted: 4/8/06
Driver side view.

bronco 060.jpg
91 hits | 51.31 KB | Posted: 4/8/06

bronco 061.jpg
90 hits | 55.09 KB | Posted: 4/8/06
Passenger side view.

bronco 062.jpg
94 hits | 58.28 KB | Posted: 4/8/06

bronco 063.jpg
130 hits | 52.92 KB | Posted: 4/8/06
Close up of highlift jack. It's mounted on two 1/2" wheel studs with wheel locks for security.

bronco 064.jpg
107 hits | 49.55 KB | Posted: 4/8/06

rocky gap 5-28-06 019.jpg
148 hits | 72.32 KB | Posted: 7/10/06
Jerry can mount added. Finished for now until I start on making the sides wrap around for extra prot...