Engine - Side.JPG
1647 hits | 81.18 KB | Posted: 2005-01-06
Another underhood pic. Here you can see the MSD 6A ignition box, MSD Blaster 2 coil, Ford Racing 9mm sparkplug wires, 2 of the largest Optima Yellow Top batteries, a 200 amp alternator, electric fan, new radiator, 14" x 4" K&N air filter w/ the X-treme Flow lid, and there is a tranny fluid cooler hiding by the radiator as well....
(Posted in: Pics)

P1300005.JPG
1919 hits | 64.73 KB | Posted: 2005-01-06
Completed rear bumper, also custom made by me and my dad. Has drilled & tapped holes for a tag, operating tag lights, and a receiver hitch welded on with additional metal plating used for strength. Trailer light hookups are also ran to the back and hook up with a standard 4 wire plug....
(Posted in: Pics)

P6040009.JPG
1644 hits | 74.63 KB | Posted: 2004-06-04
Completed front bumper, made by my father and I. The front bumper has aux head lights built into it that are turned on by a switch in the dash. Also, the bumpers are strong enough to pull from, jack up by, or push with. There is also a pull point from the front bumper that goes all the way through the bumper to a piece of plating that can be snatched from very hard. ...
(Posted in: Pics)

P6040008.JPG
2148 hits | 84.69 KB | Posted: 2004-06-04
New paintjob with Dupont basecoat/clearcoat. After painting the whole truck was wet sanded down and buffed for a show quality finish. All new lights were installed, steps were added. new mirrors put on, and a new windshield put in....
(Posted in: Pics)

P6030008.JPG
2009 hits | 66.56 KB | Posted: 2004-06-03
My new 15 subwoffer in a ported box, driven by a 1000 watt DHD amplifier. Also notice the rear cargo panels made from 3/8" polished aluminum diamondplate sheeting, and the light w/switch, the cigar lighter/auxillary power outlet and the auxillary speaker hookups for outdoor parties....
(Posted in: Pics)

P6020016.JPG
1988 hits | 63.04 KB | Posted: 2004-06-02
L&L fenderwell exit header install. Here you can see the Rancho 5000x shocks. I have the others to make the front quad shock, but I took the other 2 off because it rides smoother this way. ...
(Posted in: Pics)

P6020015.JPG
2319 hits | 59.83 KB | Posted: 2004-06-02
Front axle after gears, seals, bearings, axles, hubs and a paint job. The front end was totally taken apart and rebuilt, and has new Warn Premium hubs, 4:10 gears, new u-joints, and a locker....
(Posted in: Pics)

Backseat.jpg
2613 hits | 58.55 KB | Posted: 2004-06-02
Backseat area after I redid the entire interior. That is 3/8" thick aluminum diamondplating used for the cargo area side panels, and Pioneer 6 x 9 " speakers blast music back there also....
(Posted in: Pics)

UpFront.jpg
1466 hits | 44.06 KB | Posted: 2004-06-02
Upfront after I redid all of the interior. New seats, carpet, paint, trim pieces, etc. All of the wiring was redone as well. Doors have 6 1/2" Pioneer speakers and have all new weatherstripping also. The dash now fits a more modern single DIN size head unit too, and added guages, a steering wheel, pedal covers, a new headliner and sound deadening are there too....
(Posted in: Pics)

P6020017.JPG
1333 hits | 54.64 KB | Posted: 2004-06-02
New rims and tires. Super Swamper Irok radials mounted on Mickey Thompson Classic 2's....
(Posted in: Pics)

P6020012.JPG
2223 hits | 74.32 KB | Posted: 2004-06-02
My brand new 460. 470hp/527 ft. lbs. of torque. 1979 460 truck block bored .030" over to make 466 cid, 1970 DOVE-A closed chamber, "quench" heads have been ported & polished and the both sets of ports have been enlarged. Scorpion 1.73:1 roller rockers, 3/8" Comp Cams Magnum heat treated/hardened pushrods, & Ford Racing pushrod guideplates were also used in the heads. Pistons are Speed Pro forged flat tops w/ total seal rings making 10.5:1 compression, rods and crank are stock and have been checked for straightness and for cracks. Cam is a Lunati hydralic, lift = .531 int. & .560" exh.(w/1.73 rockers), adv. duration = 288 dg. int. & 298 dg. exh. Induction is handled by a brand new Holley 850 double pumper carb(fed by an electric fuel pump) and the intake manifold is an aluminum Weiand Stealth dual plane raised plenum....
(Posted in: Pics)