SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
1988 Ford Crown Victoria LTD “pookie”
Home/ Registry/ Ford/ LTD Crown Victoria/ “pookie” supermotors.net/registry/2410

“pookie”1988 Ford Crown Victoria LTD

130 photos documented since 2003 ♡ Follow this build

The story

*INTERIOR*
Pillar dual gauge pod
2 1/16" digital Cyberdyne Tachometer
2 1/16" digital Cyberdyne Temp. gauge
Driver side cupholder in armrest
Pilot "flat" button switches

*ENTERTAINMENT*
Sony CDX-M660
Sony XA-300 Aux-In Selector
Sony 10-disk Changer
Boss DVD player
Passenger 7" 16:9 LCD
Driver 5" LCD
2.4F capacitor
2000W AL Amp
2 Rockford Fosgate 12" 800W DVC subs
In dash mounted Bass adjust

*LIGHTING*
Stanley H4 High/Low headlamps
Cibie H1 high-beam headlamps
4-lamp relay installation
Ultra-High-Efficiency H4 bulbs
Corner turn signals installed — grimor

Photos

1988 Ford Crown Victoria LTD - Engine 1988 Ford Crown Victoria LTD - Engine Side View 1988 Ford Crown Victoria LTD - Interior - Back seat 1988 Ford Crown Victoria LTD - Interior - Center dash area 1988 Ford Crown Victoria LTD - Interior - Drivers dash / instruments 1988 Ford Crown Victoria LTD - Outside - Front Left at night in snow 1988 Ford Crown Victoria LTD - Outside - Front Right at night in snow 1988 Ford Crown Victoria LTD - Interior - Missing light cover, passenger side armrest 1988 Ford Crown Victoria LTD - Exterior - Missing passenger side under door trim 1988 Ford Crown Victoria LTD - Interior - Brake boost for trailer? 1988 Ford Crown Victoria LTD - View from back seat. 1988 Ford Crown Victoria LTD - This has more room than my closet 1988 Ford Crown Victoria LTD - Door Codes 1988 Ford Crown Victoria LTD - Front 1988 Ford Crown Victoria LTD - Drivers side 1988 Ford Crown Victoria LTD - Passenger side 1988 Ford Crown Victoria LTD - Driver rear 1988 Ford Crown Victoria LTD - Passenger rear 1988 Ford Crown Victoria LTD - Passenger front 1988 Ford Crown Victoria LTD - Front 1988 Ford Crown Victoria LTD - Front (again but got a nice shine off the chrome) 1988 Ford Crown Victoria LTD - Rear 1988 Ford Crown Victoria LTD - Drivers side 1988 Ford Crown Victoria LTD - Passengers side 1988 Ford Crown Victoria LTD - First you always need the right gear, Dremel drill, Jig saw, drill, duct tape, and of course Safety Glasses! 1988 Ford Crown Victoria LTD - The First cut.... 1988 Ford Crown Victoria LTD - Hope I got the size right, aww crap too long.... Jig saw time.... 1988 Ford Crown Victoria LTD - Yes I'm doing this in my living room, Cut the shape for Plexi-glass and compartment door.. 1988 Ford Crown Victoria LTD - put ring/handle and hinges on for compartment door. 1988 Ford Crown Victoria LTD - Liquid nail on some wood for the plexi-glass to rest on. 1988 Ford Crown Victoria LTD - WTF!! $30 for a small piece of plexi!!! 1988 Ford Crown Victoria LTD - here it is precarpet with the plexi just set in... 1988 Ford Crown Victoria LTD - Putting sides under the "floor" 1988 Ford Crown Victoria LTD - Sides on.. 1988 Ford Crown Victoria LTD - 2 Jig saws dead, time for the dremel... 1988 Ford Crown Victoria LTD - Ahh perfectly square..ish 1988 Ford Crown Victoria LTD - This is thicker than I wanted to use for a mounting board on the bottom, when the stores open I'm going with 1/4" 1988 Ford Crown Victoria LTD - WEll, this is what it looks like with the plexi in... 1988 Ford Crown Victoria LTD - ... and out 1988 Ford Crown Victoria LTD - In the trunk.... Not a bad fit for a first setting.
Browse all 130 photos

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.