SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
1993 Ford Bronco “Resurrected THRICE”
Home/ Registry/ Ford/ Bronco/ 1992–1996/ “Resurrected THRICE” supermotors.net/registry/21191

“Resurrected THRICE”1993 Ford Bronco

457 photos documented since 2009 17 years documented ♡ Follow this build

The story

It was originally purchased by a medical student. When he became a doctor in '02, he drove it to the Land Rover dealership that my brother-in-law & I were remodelling & traded it in. I bet he wishes he had kept it. My b-i-l bought it before it was wholesaled, but got bored with it after a couple of years, and abandoned it in '03. It was left in a wooded area for 6 years as he went to a KingRanch F250, then a Jag XK8, then an H2, then a Tundra, then a 4Runner...

In addition to the leaves, spider webs, mildew, vines, trees, & wasps all over it, the battery was dead, the ignition lock cylinder had to be drilled out after the keys were lost, the MLPS is bad, the starter relay is intermittent, the smog pump & A/C compressor were seized, the fuel pump was clogged, the gas was bad, the t/g window switches didn't work, the wiper motor made a LOT of noise, the wipers were torn, the brakes were rusted, the tires were almost 6 years old, the carpet was filthy, and all the fluids had to be changed.

When my g/f's nephew decided he wanted a Bronco for his first vehicle, and after searching for a month, we realized it would be cheaper to bring this one back (its first resurrection) than to buy someone else's problems. So I spent a few months fixing it, and then sold it to him. He wrecked it a month later. It took about 4 months of evenings & weekends (the 2nd resurrection) to get it driveable again.

He finally traded it for an economical car, so I bought it back. I'm overdoing it now (the 3rd resurrection) to make it the Bronco I think Ford would be building now, if they were building one now. I had to change the frame... — Steve83

Day one vs. today

Drag to compare 2009 against 2026.

1993 Ford Bronco in 2026
1993 Ford Bronco in 2009
2009 2026

Photo history

457 photos across 9 years — drag the dot to travel through this vehicle’s life. Captions are the owner’s; where there isn’t one, the AI caption fills in.

2009

2009

68 photos added — showing 8

1993 Ford Bronco - It's actually a LOT dirtier than this pic shows, and the tree by the driver's door touches the paint. This is how it looked 5 years ago: [u… 1993 Ford Bronco - I got the engine running on carb cleaner, but the belt stopped because the air pump was seized. I removed it & sprayed a BUNCH of penetrati… 1993 Ford Bronco - There was no fuel pressure, even with the relay jumpered, so I cut an access hole & pulled the FDM. All that "rust" is actually j… 1993 Ford Bronco - The residue is all over the tank; top & bottom. I've added 2 cans of Berryman's B-12 & part of a bottle of Gumout All-in-One, but the filte… 1993 Ford Bronco - Vehicle Certification (VC) Label See this: [url=http://www.supermotors.net/registry/media/72354] http://www.supermotors.net/getfile/72354/t… 1993 Ford Bronco - VECI Label IF THE IMAGE IS TOO SMALL, click it. [url=http://www.supermotors.net/registry/media/858380] http://www.supermotors.net/getfile/8… 1993 Ford Bronco - Front Axle Tag [url=http://www.supermotors.net/registry/media/544471] http://www.supermotors.net/getfile/544471/thumbnail/d44ifs96tag.jpg 1993 Ford Bronco - Original Rear Axle Tag (replaced in 2014 with one from another '93 Bronco) S837B 3L55 8 8 3F24 [url=http://www.supermotors.net/registry/med…

2010

52 photos added — showing 8

1993 Ford Bronco - Front view of a damaged 1993 Ford Bronco, showing collision damage to the headlight and bumper area. 1993 Ford Bronco - This vehicle has significant damage to its front end, including the fender and headlight assembly. 1993 Ford Bronco - The grille and headlight design suggest a 1992 Ford F-Series truck, not a 1993 Bronco. 1993 Ford Bronco - Front passenger side of a blue 1993 Ford Bronco shows damage to the fender and headlight assembly. 1993 Ford Bronco - Close-up of the driver's side door gap on a blue 1993 Ford Bronco. 1993 Ford Bronco - The front end of the vehicle shows significant damage to the bumper and headlight area. 1993 Ford Bronco - Close-up view of a damaged front bumper, showing rust and impact marks. 1993 Ford Bronco - Front end damage on a blue Ford truck, likely a 1992 model based on grille design.

2012

2 photos added

1993 Ford Bronco - This is a severely fouled orifice tube, though not with the normal type of debris. This one contains almost no metal - this is some kind of… 1993 Ford Bronco - A fin comb can be used to clean & straighten the condenser fins. The fin pitch on the old R12 condenser is 12; the fin pitch on the R134a p…

2014

80 photos added — showing 8

1993 Ford Bronco - It's a lot worse than it looks... busted w/s neither door window works driver's inside handle broken off A/C coil & low switch burned start… 1993 Ford Bronco - Build Date Stamp on hood: JUN30 1993 [url=http://www.supermotors.net/vehicles/registry/media/1035144] http://www.supermotors.net/getfile/10… 1993 Ford Bronco - Just a tiny dent in the recently-new aftermarket front bumper. 1993 Ford Bronco - The factory rear bumper is twisted more severely. 1993 Ford Bronco - I'm going to try brake fluid to remove the spray paint from the plastic centers. Paint stripper damages the clear plastic, but I can use it… 1993 Ford Bronco - The water pump is still shiny & clean, so I can't imagine why there's THIS MUCH rust in the coolant. I found out it's low because 1) the up… 1993 Ford Bronco - This is the dent that I intentionally left to remind him to be more careful. 1993 Ford Bronco - This rub pad is stretched because the rubber bumper is too sticky, and the upper sleeve is gone, allowing the arm to bounce significantly.

2015

213 photos added — showing 8

1993 Ford Bronco - 3 months of soaking in at least 4 flavors of penetrating oil, and I've managed to separate 2 of the sleeves. Today, I got fed up, and built… 1993 Ford Bronco - With my plate driven between the upper sleeve's flange & the bushing, there was enough preload on the rubber to cut the lower sleeve and ge… 1993 Ford Bronco - This was the worst one: LHS cargo bed. I had to build a 2nd tool with a smaller throat, and it still funneled. I was able to straighten it,… 1993 Ford Bronco - Like the '93XLT tub I used on my truck, this one has some GAPING holes in the factory seams. [url=http://www.supermotors.net/registry/media… 1993 Ford Bronco - Snatching a distributor out without preparing makes it much harder to put back. I prefer to mark the base in relation to the block (near th… 1993 Ford Bronco - Like every other Bronco/F engine I've seen with mounts more than a year old, at least one of these is broken. I'll probably replace both an… 1993 Ford Bronco - This gasket was installed when the reman engine went in, and although it doesn't appear to be leaking like the R side did, it was just a ma… 1993 Ford Bronco - It's much easier to get the rail out after the distributor is gone. I prefer to keep the injectors in the rail to keep fuel from dumping ou…

2016

10 photos added — showing 8

1993 Ford Bronco - This heavy plasma-cut stainless flange joins the muffler to the Y-pipe just like a stock '96 Bronco's, but without the hassles of a U-clamp… 1993 Ford Bronco - The flange was holding the muffler almost in-position, but this is the mount that will bear its weight. I'll tack it to the muffler later.… 1993 Ford Bronco - Custom-made Power Adjustable Memory Pedals 1993 Ford Bronco - Before I washed & wire-brushed it, this was a grimy old junkyard part. I prefer this to a new Chinese one. I clear-coated the metal with Du… 1993 Ford Bronco - Power Memory Signal Heated Mirror with Puddle Lamp & Off-Roading LED floods for '92-96 F-series & Broncos. The memory motors & wiring harne… 1993 Ford Bronco - This was ruined when the PO painted it black. I couldn't save it. 1993 Ford Bronco - McGard is the OEM for '92-96 Bronco spare locks, so they might be OEM for lug nuts. But even if they aren't, these are good, new, US-made p… 1993 Ford Bronco - Instead of relying on the antique hard-plastic vacuum lines or new vulcanized rubber, I collected several colors of 3mmIDx8~9mmID color-mat…

2017

1 photo added

1993 Ford Bronco - The downstream secondary air tube was broken, and too thin to weld. Since I don't have a bender to duplicate it, I just bought a heavy sili…

2019

6 photos added

1993 Ford Bronco - After a delay (building a new house & shop), I laid out the tailpipe & cut the prebent 2.25-inch stainless 90s to run like the stock pipe.… 1993 Ford Bronco - I tacked it together on the cribbing, and then built the hangers. I plan to flange the muffler-to-tailpipe connection exactly like the Y-pi… 1993 Ford Bronco - The same fabrication shop that cut the banister panels made these 3/8-inch stainless flanges, just like those at the front of the muffler (… 1993 Ford Bronco - [url=https://www.summitracing.com/parts/cel-5003/]Continental 5003 Hi-Miler Nomex/EPDM (sometimes mistakenly described as silicone) coolant… 1993 Ford Bronco - All the vacuum lines have been replaced with thick-walled (3mmIDx9mmOD) silicone tubing in the same colors as the factory used. I found the… 1993 Ford Bronco - After installing the 2nd lift in the shop, I rolled the chassis & body (separately) outside for a while.

2026

2 photos added

1993 Ford Bronco - After building a house & shop, I moved it indoors for a little while. 1993 Ford Bronco - But when I got a 2-post lift to add to the shop, I shoved the chassis out the back.

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.