KIMG0183.JPG 59 hits | 70.75 KB | Posted: 4/29/18 Decided im going to do a 'revision' of sorts to the truck. i decided i do want the truck to have 4x4...
KIMG0184.JPG 58 hits | 63.46 KB | Posted: 4/29/18 got the old heads off
KIMG0186.JPG 67 hits | 76.58 KB | Posted: 4/29/18 new cylinder heads on.
unfortunately my original Explorer valve covers did not clear the rockers. ...
KIMG0187.JPG 62 hits | 59.41 KB | Posted: 5/28/18 i originally tried to use a set of BBK 35100. unfortunatly the header of the passenger side pointed ...
KIMG0188.JPG 57 hits | 64.29 KB | Posted: 5/28/18 another view of the headers. the corner of the starter bulge would be half way into the exhaust and ...
KIMG0190.JPG 64 hits | 80.97 KB | Posted: 5/28/18 ordered some cheap Edelbrock valve covers to clear the roller rockers. got the lower intake mounted
KIMG0192.JPG 49 hits | 44.78 KB | Posted: 5/28/18 my original headers were Hedman long tube headers that defiantly interferenced with the frotn drives...
KIMG0194.JPG 47 hits | 57.2 KB | Posted: 5/28/18 the collectors also point right at the shift linkage of the trans. this may be an issue. if i decide...
KIMG0195.JPG 52 hits | 61.15 KB | Posted: 5/28/18 if need be i can cut a few inches off the collector to make room to offset
KIMG0198.JPG 54 hits | 77.31 KB | Posted: 5/28/18 old 2wd transmission is pulled to swap in a 4x4 version i bought cheap.
KIMG0202.JPG 56 hits | 86.9 KB | Posted: 5/28/18 since i had everything disconnected from the engine including tranny and EFI and i was gonna replace...
KIMG0203.JPG 63 hits | 70.21 KB | Posted: 5/28/18 i decided because i am building this truck for higher rpm range, i wanted to increase oil pressure. ...
KIMG0208.JPG 65 hits | 65.26 KB | Posted: 5/28/18 to replace the spring you need to remove the end plug which is similar to a freeze plug. you then re...
KIMG0204.JPG 58 hits | 61.05 KB | Posted: 5/28/18 new 'extreme duty' motor mounts and tranny mount from JBG.
KIMG0205.JPG 58 hits | 69.72 KB | Posted: 5/28/18 passenger side motor mount fit no problem
KIMG0206.JPG 70 hits | 72 KB | Posted: 5/28/18 driver side motor mount hit this section. a quick but with angle grinder fixed that
KIMG0207.JPG 61 hits | 64.4 KB | Posted: 5/28/18 ground down the block. you can see the spot on the motor mount it was hitting
KIMG0210.JPG 120 hits | 59.14 KB | Posted: 5/28/18 this is a new higher stall torque converter from Monster transmission. although i do not need it, it...
KIMG0211.JPG 71 hits | 53.82 KB | Posted: 5/28/18 new converter is seated in and tranny is going in. i also did a Transgo reprogramming kit to the tra...
KIMG0213.JPG 52 hits | 86.03 KB | Posted: 6/3/18 i pulled this transfer case from a f-series 87-91 at the junkyard. i went ahread and rebuilt it with...
KIMG0214.JPG 76 hits | 71.24 KB | Posted: 6/3/18 this is the stock crossemember of the F250. it was originally for a 4x4 AOD and all i did was move i...
KIMG0215.JPG 69 hits | 56.18 KB | Posted: 6/3/18 my welds may not be the best and using those crossmember supports dont quite match but with enough b...
KIMG0216.JPG 53 hits | 49.95 KB | Posted: 6/3/18 plenty of clearance now
KIMG0218.JPG 56 hits | 44.69 KB | Posted: 6/3/18 tranny and t-case are in. just need to drill holes in frame for the cossmeember
KIMG0237.JPG 79 hits | 51.63 KB | Posted: 7/28/18 start of the rewiring part of the project. have been dreading this part.
top right small harness is...
KIMG0276.JPG 71 hits | 66.57 KB | Posted: 10/14/18 new exhaust is done. i had the long tubes headers and the 2 intermidiate pipes taken to a local powd...
Revision 1
