SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
Home/ Registry/ Ford/ Bronco/ 1987–1991/ “Street Truck”/ 357 finishing up supermotors.net/registry/1725/14625

Album section

357 finishing up

From 1989 Ford Bronco “Street Truck” — documented by Tim Crase.

51 photos
← Back to this vehicle
1989 Ford Bronco - I was looking for a tranny dipstick, but I found this bigger factory cooler from a F250 instead 1989 Ford Bronco - This is the little baby factory one 1989 Ford Bronco - big one bolts into the factory holes...I flipped the samll one over to use as a PS cooler 1989 Ford Bronco - I will plumb this one in, and get rid of the tube cooler 1989 Ford Bronco - Cant even see the change behind the grille 1989 Ford Bronco - Rear veiw...cool...er..cooler 1989 Ford Bronco - One valve cover 1989 Ford Bronco - Second valve cover after fighting with the tranny dipstick for a long time 1989 Ford Bronco - I set the intake on to see how it fits 1989 Ford Bronco - Looks very cool 1989 Ford Bronco - It hits on the firewall 1989 Ford Bronco - Very cool 1989 Ford Bronco - Put the main engine harness on first thing today, then the fuel injectors and fuel rail 1989 Ford Bronco - Hooked up the fuel lines, and the heater hose ECT thingie 1989 Ford Bronco - Other side 1989 Ford Bronco - Distributor is in 1989 Ford Bronco - Now the new water pump 1989 Ford Bronco - Alternator bracket setup is on 1989 Ford Bronco - Other side 1989 Ford Bronco - Coil setup raised, cleaned, painted, and mounted 1989 Ford Bronco - See the 1" spacer on the mounts...needed to clear the valve covers 1989 Ford Bronco - Still touches...more work to do 1989 Ford Bronco - Upper manifold is mounted 1989 Ford Bronco - Just clears 1989 Ford Bronco - Side shot 1989 Ford Bronco - Lot of wires on this thing 1989 Ford Bronco - We cut off the coolant tubes for the throttle body 1989 Ford Bronco - PS bracket detailed and installed 1989 Ford Bronco - Plug wires are on, and linkage is hooked up 1989 Ford Bronco - Non-smog pump belt routing 1989 Ford Bronco - Front veiw...almost done 1989 Ford Bronco - All ready to fire it up 1989 Ford Bronco - We ran it, no exhaust, just the headers...wow..LOUD. 1989 Ford Bronco - I drilled and assembled the pod and wiring on the bench....Dont do this. 1989 Ford Bronco - Doing the wiring is ok, but dont mount the pod yet 1989 Ford Bronco - I also ran all the wires together, another waste of time 1989 Ford Bronco - Trial fitting the Pod 1989 Ford Bronco - Wires will be hidden behind the interior panels 1989 Ford Bronco - Took me an hour and a half to figure out that I can NOT get that screw in. 1989 Ford Bronco - So....I ripped the pod back off 1989 Ford Bronco - Countersunk the holes 1989 Ford Bronco - There..all mounted 1989 Ford Bronco - Without the flash 1989 Ford Bronco - Countersunk screws look good I think 1989 Ford Bronco - Pulled the grille again today so I can finish my wiring 1989 Ford Bronco - you can see the sending unit for my tranny temp guage 1989 Ford Bronco - Tomorows project...Maybe 1989 Ford Bronco - Hard to see them, but I installed hood lights 1989 Ford Bronco - This is where my MSD box used to be, So I filled the holes with wires 1989 Ford Bronco - All done...even the linkage cap thingy 1989 Ford Bronco - Other side