Embassy Vic > 2001 Ford Crown Victoria > open folder Corner lamp conversion to turn signals

The corner/marker lamps on Crown Victorias does not act as turn signal, leaving no visible turn sign...
Side marker before.gif
1137 hits | 11.01 KB | Posted: 9/27/06
The corner/marker lamps on Crown Victorias does not act as turn signal, leaving no visible turn sign...
Side marker after.gif
Side marker after.gif
830 hits | 10.68 KB | Posted: 9/27/06
First, the corner lamp must be removed. There is a nut, under the trim panel, that runs along the ra...
Corner lamp nut removal.JPG
1056 hits | 27.9 KB | Posted: 9/27/06
First, the corner lamp must be removed. There is a nut, under the trim panel, that runs along the ra...
The back side of the corner lamp and its respective wiring.
Corner Lamp wiring.JPG
783 hits | 30.97 KB | Posted: 9/27/06
The back side of the corner lamp and its respective wiring.
Use a test light and a needle to determine which of the three wires is the turn signal. On my '01, t...
Turn signal harness.JPG
807 hits | 23.92 KB | Posted: 9/27/06
Use a test light and a needle to determine which of the three wires is the turn signal. On my '01, t...
I used a knife to peel back the wiring loom to gain access to the correct turn signal wire.
Turn signal wiring.JPG
783 hits | 36.05 KB | Posted: 9/27/06
I used a knife to peel back the wiring loom to gain access to the correct turn signal wire.
I ran new wiring in a wire loom, wrapped up with electrical tape to ensure an OEM appearance.
New wiring.JPG
762 hits | 34.83 KB | Posted: 9/27/06
I ran new wiring in a wire loom, wrapped up with electrical tape to ensure an OEM appearance.
The passenger side corner lamp harness, consisting of a brown wire and a black ground wire. It is th...
Corner lamp harness.JPG
854 hits | 34.57 KB | Posted: 9/27/06
The passenger side corner lamp harness, consisting of a brown wire and a black ground wire. It is th...
The new wiring, going in from the corner lamp's position.
New wiring1.JPG
771 hits | 30.41 KB | Posted: 9/27/06
The new wiring, going in from the corner lamp's position.
I ran the wiring under the fender and up in front of the radiator support.
New wiring underside.JPG
818 hits | 29.49 KB | Posted: 9/27/06
I ran the wiring under the fender and up in front of the radiator support.
The new wiring can see seen. Look for the red wire.
New wiring fed.JPG
737 hits | 37.63 KB | Posted: 9/27/06
The new wiring can see seen. Look for the red wire.
The new wiring, passing by the turn signal connector.
New wiring fed1.JPG
792 hits | 32.7 KB | Posted: 9/27/06
The new wiring, passing by the turn signal connector.
The factory turn signal wiring can be seen in the lefthand corner of the picture. The new wiring is ...
New wiring fed 2.JPG
756 hits | 34.74 KB | Posted: 9/27/06
The factory turn signal wiring can be seen in the lefthand corner of the picture. The new wiring is ...
The new wire, spliced into the ground and before I cut the ground going back towards the frame.
Corner lamp splice.JPG
758 hits | 22.29 KB | Posted: 9/27/06
The new wire, spliced into the ground and before I cut the ground going back towards the frame.
The new wiring, spliced into the turn signal wiring, wrapped up with electrical tape and secured wit...
Turn signal splice.JPG
930 hits | 33.86 KB | Posted: 9/27/06
The new wiring, spliced into the turn signal wiring, wrapped up with electrical tape and secured wit...
It works.
Success.JPG
1489 hits | 31.93 KB | Posted: 9/27/06
It works.
Here's a vid, courtesy of Nell's Crown Victoria website, that shows the results of modification.
Nells Vic Blinkers.avi
1410 hits | 446.05 KB | Posted: 9/27/06
Here's a vid, courtesy of Nell's Crown Victoria website, that shows the results of modification.