104_0453.JPG
3149 hits | 64.24 KB | Posted: 9/14/04
Warn 9k winch, 55 lbs. Solenoid, fairlead and wiring, 20lbs. add the mount and total weight apx. 10...

104_0454.JPG
3163 hits | 41.51 KB | Posted: 9/14/04
mount is made of 8" Structural C channel, 11.5# with 2" sides, bottom is equivalent to 1/4" steel, b...

104_0455.JPG
2801 hits | 45.48 KB | Posted: 9/14/04
before cutting this 38" piece is 33lbs. after it was 26.

104_0457.JPG
2914 hits | 65.04 KB | Posted: 9/14/04

104_0458.JPG
3294 hits | 57.62 KB | Posted: 9/14/04
test fit after cutting.

104_0460.JPG
2962 hits | 62.26 KB | Posted: 9/14/04
The rear 2" side was cut down to about 1.25". Just enough room to clear tranny lines

104_0462.JPG
3237 hits | 61.57 KB | Posted: 9/14/04

104_0475.JPG
3421 hits | 60.16 KB | Posted: 9/14/04

104_0466.JPG
2800 hits | 56.06 KB | Posted: 9/14/04
This mount does not stick out way forward of the bumper/frame.

104_0468.JPG
3423 hits | 60.48 KB | Posted: 9/14/04

104_0475.JPG
3645 hits | 60.16 KB | Posted: 9/14/04
Same pic, fairlead added

104_0476.JPG
3057 hits | 67.71 KB | Posted: 9/14/04

104_0477.JPG
2963 hits | 46.65 KB | Posted: 9/14/04

104_0478.JPG
4307 hits | 50.47 KB | Posted: 9/14/04

104_0480.JPG
2891 hits | 60.55 KB | Posted: 9/14/04

105_0508.JPG
3135 hits | 53.46 KB | Posted: 9/22/04
Care on the winch mount is needed, as the fairlead bolt does need about 1" of clearance or it will t...

105_0509.JPG
2878 hits | 58.59 KB | Posted: 9/22/04
good shot of winch mount to frame brackets, 2 for each side (one is back behind the bumper mount bra...

105_0514.JPG
2726 hits | 65.63 KB | Posted: 9/22/04
shot of mount from underneath looking toward the front. Note how it's cut back around the accordian...

105_0519.JPG
2663 hits | 57.98 KB | Posted: 9/22/04
rearmost bracket

105_0516.JPG
2661 hits | 58.85 KB | Posted: 9/22/04
one more shot looking underneath, toward the driver side of the vehicle.

105_0517.JPG
2581 hits | 43.33 KB | Posted: 9/22/04
closeup of solenoid

105_0518.JPG
2607 hits | 50.76 KB | Posted: 9/22/04
solenoid mount again, this time with Grille removed. Note black plastic edging to protect cables. ...

105_0506.JPG
2778 hits | 50.36 KB | Posted: 9/22/04
beginning to work on the shackle to frame attachment. 1" x 2" x 6" steel

105_0507.JPG
2604 hits | 49.71 KB | Posted: 9/22/04
yep, that's 6"

105_0520.JPG
2963 hits | 47.66 KB | Posted: 9/22/04
once the 1" hole is cut, it needs to be carefully measured for the (2) 1/2" mounting holes. (the 1/...

105_0512.JPG
2885 hits | 53.76 KB | Posted: 9/22/04
end result. Well not quite. It needs to ber purdied up at this point.

105_0513.JPG
2774 hits | 58.19 KB | Posted: 9/22/04
another angle

105_0542.JPG
2766 hits | 64.23 KB | Posted: 12/22/04
some of my recovery stuff, 6T WLL snatch block,10' x 2"(double wound) tree strap, 3/4" 4.75WLL D sha...