SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
1992 Ford Bronco “the bitch”
Home/ Registry/ Ford/ Bronco/ 1992–1996/ “the bitch” supermotors.net/registry/17507

“the bitch”1992 Ford Bronco

documented by redrumybronco 54 photos documented since ♡ Follow this build

The story

I enjoy working on my truck. I have done all of my modifications using simple and cheap garage tools. I have saved thousands of dollars doing it myself. — redrumybronco

Photos

1992 Ford Bronco — Started off by removing part of the rain gutter 1992 Ford Bronco — cut a slot in the sheet metal where the horizontal joint is visible 1992 Ford Bronco — Welded a reinforcemant 1/8"x1" (you can barely see it sticking out) 1992 Ford Bronco — this is the sheet metal reinforcement 1992 Ford Bronco — filled and primered, not ready for paint yet Close-up of a gray primered body panel corner on a vehicle under a tent 1992 Ford Bronco interior showing two blue speakers and a black toolbox in the cargo area Blue NOS nitrous bottle and NOS controller mounted in a vehicle interior panel 1992 Ford Bronco — 150 watt Alpine amp Close-up of a blue NOS nitrous bottle and NOS electronics mounted in a trunk 1992 Ford Bronco — amp for mid range speakers 1992 Ford Bronco — Cooling fan light 1992 Ford Bronco — Vehicle interior showing two blue cylindrical speakers with purple lights, facing rearward. Seats and dashboa… 1992 Ford Bronco — Drill and tap Metal linkage joint and rod under a vehicle with masking tape nearby Close-up of a metal engine part covered with tape and paper towels 1992 Ford Bronco — locktite and srew in 1992 Ford Bronco — only time will tell if this will hold, but this is much better than before 1992 Ford Bronco — Black painted upper rear quarter panel and door window frame of a vehicle under a tent Close-up of dark-colored vehicle body panel with window trim and a small antenna-like protrusion. Watermark r… 1992 Ford Bronco — Swing-away spare tire carrier with mounted all-terrain tire and Hi-Lift jack Spare tire carrier modification with Hi-Lift jack mounted Close-up of a black metal spare tire carrier with a tire and brake rotor visible 1992 Ford Bronco — body damage by spare tire carrier 1992 Ford Bronco — welded a metal bracket 1992 Ford Bronco — some paint to prevent rust Red Lincoln Electric Weld Pak 3200 welding machine on a cart with four wheels Red welding cart with black frame and wheels Red Lincoln Electric Weld Pak welding machine on a four-wheeled cart 1992 Ford Bronco — The Rancho kit came with two add-a-leafs and so I had to remove a stock leaf from each side. Recycled the old… 1992 Ford Bronco — 2.5 degree shim plus cut up leafs = 1-1/2" lift The Rancho kit raises the rear 3" and the front 4". Need an a… 1992 Ford Bronco — I had to devise a way so that the leaf center bolt would be able to fit into the stock shim 1992 Ford Bronco — bottom of rancho shim, the hole is tappered 1992 Ford Bronco — cut a shock mount sleeve and welded the edge in to fill in the tappered hole 1992 Ford Bronco — looking from the top, pipe wedge is not welded to aluminum degree shim just wedged in 1992 Ford Bronco — although this looks kinda funny, the three cut up leafs only lift about 1". It is way better than the smaller… 1992 Ford Bronco — close up of the leaf center bolt catching the pipe wedge 1992 Ford Bronco — driveline angle corrected 1992 Ford Bronco — removed shock mounts for re-positioning 1992 Ford Bronco — shock mount welded at 15 degrees
Browse all 54 photos
See every Ford Bronco in the registry The 1992–1996 Ford Bronco registry

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.