mac01.JPG
1070 hits | 80.85 KB | Posted: 1/16/07
Simple F150 performance mods from MAC and Edge Products

[b]Story and photos by Arthur Jens...

mac02.JPG
512 hits | 49.5 KB | Posted: 1/16/07
The Edge Products Evolution programmer includes everything you need for a clean, easy install, inclu...

mac03.JPG
487 hits | 56.27 KB | Posted: 1/16/07
Start by removing the drivers side dash access panel.

mac04.JPG
437 hits | 58.53 KB | Posted: 1/16/07
Feed the Edge cable up from the bottom of the dash being careful to avoid any sharp corners that cou...

mac05.JPG
438 hits | 58.19 KB | Posted: 1/16/07
You want to leave just enough cable at the bottom to reach the OBD2 port near the drivers right knee...

mac06.JPG
443 hits | 60.66 KB | Posted: 1/16/07
Feed the cable around the edge of the dash and through the back of the new Edge housing. Leave a lit...

mac07.JPG
471 hits | 59.54 KB | Posted: 1/16/07
With the key off, plug the cable into the OBD2 port and the back of the Evolution programmer, then u...

mac08.JPG
424 hits | 62.49 KB | Posted: 1/16/07
Turn the key on and follow the on-screen prompts to finish setting up the Evolution. Once everything...

mac09.JPG
441 hits | 81.79 KB | Posted: 1/16/07
Now that the programmer is done we can move on to the engine bay. The stock intake is large, ugly, a...

mac10.JPG
518 hits | 75.33 KB | Posted: 1/16/07
The air inlet tube simply pulls out of the air box. On the body end it's held in with a simple rubbe...

mac11.JPG
437 hits | 56.66 KB | Posted: 1/16/07
Remove this sensor fitting on the passenger side of the air box near the firewall by turning the gre...

mac12.JPG
496 hits | 59.86 KB | Posted: 1/16/07
To unlock the MAF sensor lead, press down on the red clip and pull straight out.

mac13.JPG
431 hits | 65.67 KB | Posted: 1/16/07
These bolts hold the air box in place on the engine.

mac14.JPG
460 hits | 87.98 KB | Posted: 1/16/07
With the bolts removed, the air box can be pulled away from the throttle body by hand, the MAF senso...

mac15.JPG
388 hits | 59.16 KB | Posted: 1/16/07
Using one of the provided clamps, loosely attach the elbow to the throttle body.

mac16.JPG
526 hits | 65.14 KB | Posted: 1/16/07
A special bit to remove the MAF sensor is included with the intake, remove and save the screws, then...

mac17.JPG
466 hits | 62.6 KB | Posted: 1/16/07
Using the supplied Philips head screws, install the MAF sensor into the new billet housing.

mac18.JPG
544 hits | 67.41 KB | Posted: 1/16/07
Mount the new MAF housing with sensor installed into the elbow fitting on the engine with the flow a...

mac19.JPG
440 hits | 67.38 KB | Posted: 1/16/07
Bolt the filter flange and mounting pegs to the heat shield with the six provided 10mm bolts.

mac20.JPG
481 hits | 73.37 KB | Posted: 1/16/07
The heat shield presses into two rubber grommets that must be installed in two existing holes in the...

mac21.jpg
426 hits | 64.72 KB | Posted: 1/16/07
Reconnect the MAF sensor to its harness lead by pressing in until it locks.

mac22.JPG
430 hits | 49.91 KB | Posted: 1/16/07
Connect this rear sensor tube to its new billet fitting on the elbow.

mac23.JPG
413 hits | 87.81 KB | Posted: 1/16/07
Using the largest clamp, attach the new MAC filter to the mounting flange and tighten it in place.

mac24.JPG
410 hits | 73.6 KB | Posted: 1/16/07
Once everything is aligned and properly positioned, tighten the remaining clamps, but don't over tig...

mac25.JPG
417 hits | 85.92 KB | Posted: 1/16/07
Here is the finished intake, much simpler and cleaner then the stock unit.

mac26.JPG
458 hits | 77.15 KB | Posted: 1/16/07
Now for the exhaust. Here is the complete MAC cat-back system. The black coating prevents rust and c...

mac27.JPG
442 hits | 76.16 KB | Posted: 1/16/07
Of course this job is easier with the truck on the lift but this is something you could do simply in...

mac28.JPG
373 hits | 74.91 KB | Posted: 1/16/07
With the clamp loose, work the stock system free by pushing it towards the back of the truck while r...

mac29.JPG
455 hits | 94.77 KB | Posted: 1/16/07
Install the new connector tube into the stock front section but leave it loose so it can rotate to m...

mac30.jpg
434 hits | 71.97 KB | Posted: 1/16/07
With the new studs screwed into the connecter pipe and muffler rear flanges, hang the new muffler us...

mac31.JPG
386 hits | 74.8 KB | Posted: 1/16/07
Hang the front exhaust outlet using the stock mount, then thread the nuts onto the studs by hand.

mac32.JPG
489 hits | 62.04 KB | Posted: 1/16/07
The rear outlet needs a new mount attached to the frame, the bracket can bolt on here above the shac...

mac33.JPG
373 hits | 67.84 KB | Posted: 1/16/07
With the pipes hung, bolt the two together and align the tips before tightening the whole system. A ...

mac34.JPG
395 hits | 57.04 KB | Posted: 1/16/07
Here is the finished product back on the ground. The bolt-on tips make re-aligning or replacing them...

mac35.JPG
463 hits | 73.57 KB | Posted: 1/16/07
Back on the LA Performance Division Dynojet for an after test, and with the Edge programmer set to p...

mac36.JPG
506 hits | 73.87 KB | Posted: 1/16/07
Out on the road the improved midrange made the truck much more enjoyable to drive. The exhaust and i...