1984 Ford Bronco
Owner: JDoumont 
From: Lincoln University, PA, U.S.A.        (Other registries in PA)
Year, Make, & Model: 1984 Ford Bronco        (Other Ford Broncos)
Avatar:
Nickname: Bronco84
Mileage: 86000
Engine: 302 2bbl Carb
Drivetrain: 3/4 Ton HP D44, D60 rear, Twin Stick NP205, NP435 4 speed.
Notes:
Last Updated: 6/30/2007
Hits: 3066
Album
Folder Hits Comments Created Updated
folder NP205 Twin Stick11005,86406/25/076/25/07
folder First Day Home3001,04406/30/076/30/07
Newest Media Files
DSC00904.JPG
339 hits | 60.62 KB | Posted: 6/30/07

DSC00903.JPG
330 hits | 64.75 KB | Posted: 6/30/07

DSC00900.JPG
375 hits | 42.8 KB | Posted: 6/30/07

DSC01072.JPG
524 hits | 64.99 KB | Posted: 6/25/07

Install the new shift rail parts.
DSC01071.JPG
452 hits | 45.09 KB | Posted: 6/25/07

The shift rail should look like this when your finished
DSC01067.JPG
464 hits | 43.53 KB | Posted: 6/25/07

Place the rail in a vice and using a grinder slowly and evenly remove the extra material
DSC01065.JPG
557 hits | 47.05 KB | Posted: 6/25/07

Rear shift rail.
DSC01062.JPG
478 hits | 62.79 KB | Posted: 6/25/07

Place a 1/4-20 bolt through the shift rail and tap it out with a hammer.
DSC01061.JPG
538 hits | 49.8 KB | Posted: 6/25/07

Move rail to center position and knock the roll pin out. It will fall through and out the bottom access panel with the freeze plug.
Most Viewed Files
DSC01052.JPG
904 hits | 56.09 KB | Posted: 6/25/07

Twin Stick Conversion kit from JB Custom Fabrication
DSC01053.JPG
638 hits | 50.88 KB | Posted: 6/25/07

NP205 From a 78 F250
DSC01065.JPG
557 hits | 47.05 KB | Posted: 6/25/07

Rear shift rail.
DSC01061.JPG
538 hits | 49.8 KB | Posted: 6/25/07

Move rail to center position and knock the roll pin out. It will fall through and out the bottom access panel with the freeze plug.
DSC01072.JPG
524 hits | 64.99 KB | Posted: 6/25/07

Install the new shift rail parts.
DSC01057.JPG
480 hits | 64.89 KB | Posted: 6/25/07

Remove bottom cover (After Draining fluid)
DSC01062.JPG
478 hits | 62.79 KB | Posted: 6/25/07

Place a 1/4-20 bolt through the shift rail and tap it out with a hammer.
DSC01067.JPG
464 hits | 43.53 KB | Posted: 6/25/07

Place the rail in a vice and using a grinder slowly and evenly remove the extra material
DSC01055.JPG
463 hits | 58 KB | Posted: 6/25/07

Maintenance & Modification Logs
This user hasn't added any log entries, yet.
About SuperMotors | Contact Us | FAQ/Help | Legal
Copyright © 1998-2024 Web Design Solutions, Inc.
All rights reserved. Duplication & reproduction is strictly prohibited.
SuperMotors.net v5.0.2 ChangeLog