SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
Home/ Registry/ Ford/ Probe/ 1993–1997/ 1996 Probe/ Turbo motor rebuild supermotors.net/registry/7120/27717

Album section

Turbo motor rebuild

From 1996 Ford Probe — documented by Jasbo.

118 photos 1 video
← Back to this vehicle
1996 Ford Probe - Close-up view of an engine piston, showing signs of wear and carbon deposits. 1996 Ford Probe - This piston shows significant damage, likely from engine failure during operation. 1996 Ford Probe - This image shows a damaged piston within an engine cylinder, indicating internal engine wear or failure. 1996 Ford Probe - A piston and connecting rod assembly, likely from an engine rebuild, rests on a workbench surface. 1996 Ford Probe - Exhaust pipe section with flanges, resting on plywood. 1996 Ford Probe - A turbo exhaust manifold with a wastegate, wrapped in heat tape, is hung on a green lattice wall. 1996 Ford Probe - Front mount intercooler installation visible on a vehicle with pop-up headlights, suggesting engine modification. 1996 Ford Probe - New engine valve springs laid out on a workbench, ready for installation. 1996 Ford Probe - Close-up view of a car's engine bay, focusing on the radiator and cooling fans during a repair or upgrade. 1996 Ford Probe - A single engine lifter is shown resting on boxes from 'Top Line' and 'Chicago USA'. 1996 Ford Probe - A used piston and connecting rod are shown side-by-side on a workbench, likely for engine repair or rebuild. 1996 Ford Probe - Close-up of an AiResearch turbocharger, showing internal components and branding. 1996 Ford Probe - A man poses with a car engine that has a turbocharger attached, suspended by a hoist in a garage. 1996 Ford Probe - Close-up of a disassembled oil pump housing, showing internal components and gasket. 1996 Ford Probe - Engine assembly with turbocharger, likely for a performance vehicle, undergoing rebuild or installation. 1996 Ford Probe - Engine and transmission assembly, likely out of a vehicle for repair or rebuild. 1996 Ford Probe - Custom engine assembly a turbocharger and exhaust system, likely undergoing a rebuild or modification. 1996 Ford Probe - A turbocharged engine assembly is shown, suspended and ready for installation. 1996 Ford Probe - A box containing six Wiseco pistons is shown, along with two Wiseco decals and some paperwork. 1996 Ford Probe - Box of six new pistons, each with installation instructions on a sticker. 1996 Ford Probe - Intake valves not even close to entering the pockets.... 1996 Ford Probe - exhaust valves fouling 1996 Ford Probe - In this pic... you can see rub marks I created by twirling the valve in the valve guide, 1996 Ford Probe - A new piston and connecting rod sit next to a used one, with a crankshaft in the background, likely for an engine rebuild. 1996 Ford Probe - Comparison of a new piston and connecting rod with a used one. 1996 Ford Probe - Comparison of a new piston and connecting rod assembly with a used one. 1996 Ford Probe - A complex automotive wiring harness is laid out on a workbench alongside various tools used for electrical work. 1996 Ford Probe - A disassembled car wiring harness is spread across a workbench, surrounded by tools and electrical components. 1996 Ford Probe - Engine oil pump housing with visible casting marks and a seal. 1996 Ford Probe - Close-up of an engine oil pump housing, showing its internal components and gasket. 1996 Ford Probe - Close-up of an engine intake manifold, possibly for a Ford Probe, with a red fuel pressure regulator mounted. 1996 Ford Probe - A close-up view of an engine lifter part, held in a person's hand. 1996 Ford Probe - Engine lifter part shown on packaging boxes from Top Line Engineering and Chicago USA. 1996 Ford Probe - A turbo blow-off valve is shown, likely part of a vehicle's engine system, in a workshop environment. 1996 Ford Probe - Close-up of a worn crankshaft, indicating potential engine damage or turbo motor issues. 1996 Ford Probe - Close-up view of an engine block's bearing saddles and caps, likely during a rebuild or inspection. 1996 Ford Probe - Engine block disassembled on a workbench, ready for rebuild. 1996 Ford Probe - Multiple vehicle wiring harnesses are laid out on a worn concrete surface, possibly for repair or replacement. 1996 Ford Probe - Engine wiring harness and associated electronic control unit (ECU) laid out on a concrete surface. 1996 Ford Probe - Engine wiring harness components spread out on a garage floor. 1996 Ford Probe - A person stands by as a car engine is hoisted by chains in a garage setting. 1996 Ford Probe - A silver V6 DOHC 24 valve intake manifold rests on a bed of gravel and grass. 1996 Ford Probe - Silver intake manifold with V6 DOHC 24-VALVE markings, likely for a performance engine rebuild. 1996 Ford Probe - V6 DOHC 24-valve intake manifold, likely from a Mazda or Ford vehicle. 1996 Ford Probe - Close-up of various electrical wires, each prepared with a metal connector for electrical connection. 1996 Ford Probe - Engine block assembly with pistons and a pulley system, resting on a wooden block. 1996 Ford Probe - Engine wiring harness with an Engine Control Unit (ECU) laid out on a concrete floor. 1996 Ford Probe - Engine block with six cylinder bores, likely for a V6 engine, on a workbench. 1996 Ford Probe - Close-up of a clean engine block, showing the cylinder bores and internal passages. 1996 Ford Probe - Close-up view of an engine block's cylinders, revealing the honed interior surfaces. 1996 Ford Probe - Close-up view of a clean engine cylinder block, likely undergoing a rebuild or inspection. 1996 Ford Probe - Close-up view of an engine block, focusing on the cylinder bores and internal structure. 1996 Ford Probe - A person is working with a wiring harness and a diagram, likely for a vehicle repair or modification. 1996 Ford Probe - Two metal fuel rails are shown on top of a water heater, likely during a repair or rebuild process. 1996 Ford Probe - Disassembled fuel injectors and fuel rail with assorted tools and hardware on a workbench. 1996 Ford Probe - A V6 DOHC 24-valve intake manifold is shown on a workbench, suggesting engine work or repair. 1996 Ford Probe - Mechanic works on engine block and crankshaft assembly, with a black car visible in the background. 1996 Ford Probe - Mechanic works on engine block and crankshaft assembly in a garage setting. 1996 Ford Probe - Close-up view of a disassembled engine's crankshaft and internal components, showing wear and oil residue. 1996 Ford Probe - Engine block with crankshaft and connecting rods, tools on table during a rebuild. 1996 Ford Probe - Disassembled engine block with crankshaft visible, indicating a repair or rebuild process. 1996 Ford Probe - Engine block casting with bearing caps installed, ready for crankshaft. 1996 Ford Probe - Close-up of an engine block, showing the main bearing saddles and some attached components. 1996 Ford Probe - An electronic circuit board, possibly for a vehicle, is shown with various components and wiring. 1996 Ford Probe - A used piston and connecting rod assembly are shown next to a new one, likely for a turbo motor rebuild. 1996 Ford Probe - Man poses inside the engine bay of a 1996 Ford Probe. 1996 Ford Probe - Engine bay of a purple car with the engine removed, showing disassembled components and drive axles. 1996 Ford Probe - Engine bay of a purple vehicle undergoing turbocharger installation, an MSD ignition box and extensive wiring. 1996 Ford Probe - Close-up of a crankshaft, likely for engine repair or rebuild. 1996 Ford Probe - A crankshaft sits on a workbench next to a rag and some socket wrenches. 1996 Ford Probe - A disassembled engine crankshaft with visible markings sits on a workbench, surrounded by engine components. 1996 Ford Probe - A black exhaust pipe is suspended by a wire in front of a wooden fence, suggesting it is a replacement part. 1996 Ford Probe - Close-up of engine bay components, including a blue silicone hose and metal piping. 1996 Ford Probe - New valve springs are laid out on a workbench, ready for installation into an engine. 1996 Ford Probe - The engine bay of a purple car is shown with various hoses and wires disconnected during a rebuild. 1996 Ford Probe - A V6 DOHC 24-VALVE intake manifold is visible behind a crankshaft, suggesting engine work. 1996 Ford Probe - Disassembled engine cylinder heads and associated parts laid out on a workbench for repair or rebuild. 1996 Ford Probe - A bent exhaust pipe is supported by a wooden dowel in front of a backyard fence. 1996 Ford Probe - The interior of a car is shown with the dashboard removed, revealing exposed wiring and components, suggesting a repair or modification is… 1996 Ford Probe - A pair of bright yellow brake calipers and their mounting bracket are displayed on a bed of small stones and dirt. 1996 Ford Probe - A close-up view of a red fuel pressure regulator and its attached gauge. 1996 Ford Probe - A red fuel pressure regulator is attached to a fuel line and has a pressure gauge. 1996 Ford Probe - Engine cylinder bore showing cross-hatching from honing process. 1996 Ford Probe - A bright yellow brake caliper sits on gravel, with a dark vehicle in the background. 1996 Ford Probe - A disassembled engine cylinder head rests on a workbench, surrounded by tools and parts. 1996 Ford Probe - A fuel rail assembly with a red adjustable fuel pressure regulator and a pressure gauge is shown, likely for a turbo motor rebuild. 1996 Ford Probe - Close-up of a black textured Mazda valve cover with silver lettering and mounting holes. 1996 Ford Probe - Engine parts, including valve covers and exhaust manifolds, are displayed on a gravel surface. 1996 Ford Probe - Engine parts, including two valve covers and two exhaust manifolds, are laid out on a gravel surface. 1996 Ford Probe - Close-up view of an engine block, showing three cylinders and parts of the pistons within. 1996 Ford Probe - Engine valve cover with illuminated oval cutouts, possibly for custom lighting. 1996 Ford Probe - The machined surface of an engine's cylinder block shows three precisely bored cylinders. 1996 Ford Probe - A disassembled distributor is held in a vise on a workbench, surrounded by other engine parts. 1996 Ford Probe - A car distributor is clamped in a vise, ready for inspection or repair. The rotor and electrical connections are clearly visible. 1996 Ford Probe - Close-up of a car distributor assembly, possibly for a Ford Probe, secured in a vise. 1996 Ford Probe - A person is working on a car engine piston, which is secured in a vise in a garage setting. 1996 Ford Probe - Mechanic works on a car engine piston held in a vise in a garage. 1996 Ford Probe - Plastic gauge is used to measure bearing clearance on an engine part during a turbo motor rebuild. 1996 Ford Probe - Feeler gauge used to measure engine part clearance. 1996 Ford Probe - Measuring engine bearing clearance with a plastic gauge strip. 1996 Ford Probe - Close-up view of a modified engine bay, focusing on the intake system and brake components. 1996 Ford Probe - Engine bay view of a Mazda V6 engine modified with a turbocharger and aftermarket intake system. 1996 Ford Probe - Customized engine bay aftermarket performance parts and a Summit Racing flywheel box. 1996 Ford Probe - Engine bay view a V6 engine with turbocharger modifications and associated plumbing. 1996 Ford Probe - Here's my first un-tunned Dyno with the Turbo setup... the pull was made at approx 7psi to 6k rpm.. 1996 Ford Probe - Heres a clip from a larger video of my dyno pull @ 7psiVideo 1996 Ford Probe - A purple 1996 Ford Probe is parked on a grassy lot next to a building and a trailer. 1996 Ford Probe - A dark blue coupe is positioned on a dynamometer with its hood open, possibly for engine work or testing. 1996 Ford Probe - Engine bay view shows a modified Mazda V6 engine with a turbocharger installed. 1996 Ford Probe - A purple car is on a dynamometer in a garage, with its hood open and wires connected. 1996 Ford Probe - This 1996 Ford Probe is seen from the rear 3/4 angle, with its distinctive taillights and "PROBE 24V" badging clearly visible. 1996 Ford Probe - Close-up view of two fuel injectors, showing their metallic tops and green seals against a wooden background. 1996 Ford Probe - A detailed view of a metal fuel injector, showing its top surface and a central opening. 1996 Ford Probe - A fuel injector, likely from a turbo motor rebuild, is shown in detail. 1996 Ford Probe - Fuel injector part shown in detail, likely for engine work. 1996 Ford Probe - Two fuel injectors are shown from the top, resting on a wooden surface against a dark background. 1996 Ford Probe - avatar 1996 Ford Probe - Not bad for being relatively untuned... Still alot of room for improvement,,, 1996 Ford Probe - Close-up of a turbocharger, identified by markings as a GT35 model, likely part of an engine rebuild.