SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
1984 Ford Bronco
Home/ Registry/ Ford/ Bronco/ 1980–1986/ 1984 Bronco supermotors.net/registry/21944

1984 Ford Bronco

13 photos documented since 2010 5 years documented ♡ Follow this build

The story

4" suspension lift
3" body lift
16" x 10" MT classic 2 rims
37" tires — 351bronco84

Photos

1984 Ford Bronco - 1984 351c Bronco Had been sitting in my shed for a few years like this waiting for time & money for resto! 1984 Ford Bronco - Got the body of the chassis and giving it a degrease ready to pull 351c motor, c6 tranny, 9" diff & dana 44 out. 1984 Ford Bronco - A Ford Bronco body sits atop its chassis in a workshop, undergoing restoration. 1984 Ford Bronco - 351c had only done 120k km's but must have never had oil changes done. Motor was stuffed and filled with black sludge. So much for just a f… 1984 Ford Bronco - Gave the open chamber heads a cleanup and removed any lumps etc from the ports. New valves, guides etc 1984 Ford Bronco - Getting ready to build the Megasquirt ECU. I am going to fabricate a aluminium sheet metal manifold and I have Hayabusa throttle bodies wit… 1984 Ford Bronco - Bare board with just one connector installed. This is a long process to solder all together but hopefully it will all be worth it! 1984 Ford Bronco - Soldering done, just had to clean & seal the board & then program it for my engine. 1984 Ford Bronco - Final Megasquirt ECU ready to wire up! 1984 Ford Bronco - Used a gazebo in my shed as a sandblasting/painting booth. Wont use it to paint the body as to much dust floating around from blasting but… 1984 Ford Bronco - Motor partly back together, replaced pretty much everything. Wished I had grit blasted before I dismantled it. Would make it alot easier to… 1984 Ford Bronco - Pile of stuff to be grit blasted! I hate to think how many hours I have spent blasting. Gone through about 150 ceramic tips! 1984 Ford Bronco - Sump after blasting. 1984 Ford Bronco - After blasting I gave everything a coat or Wattyl PR250 then DTM985. These are marine coatings. Hopefuly this thing wont rust again in my l… 1984 Ford Bronco - More parts that I painted. 1984 Ford Bronco - Having trouble getting the pattern right when installing new ring & pinion to the Dana 44. The ford 9" is a brilliant design, so easy… 1984 Ford Bronco - The frame of a vehicle is suspended on stands within a temporary tent structure, likely for restoration or painting. 1984 Ford Bronco - Chassis looked terrible but once I cleaned it up a bit I found there was only minimal surface rust to blast off. 1984 Ford Bronco - Because it took so long with the small grit blaster, I had to blast a bit then prime it, then blast some more the next day and prime it etc… 1984 Ford Bronco - Installing new ring & pinion to the 9" diff plus replacing all bearings/seals etc. 1984 Ford Bronco - Custom aluminum intake manifold with four carburetor mounts sits on a workbench. 1984 Ford Bronco - Custom aluminum intake manifold with four carb openings, installed on an engine. 1984 Ford Bronco - The Hayabusa throttle bodies mounted, have installed bigger injectors and will make a cold air intake when body chassis etc are back togeth… 1984 Ford Bronco - Starting to make my intake manifold, cut it out with a die grinder. 1984 Ford Bronco - Surprising how much work goes into a sheet metal intake! 1984 Ford Bronco - Starting to come together! 1984 Ford Bronco - The chassis of a vehicle is shown, supported by jack stands, with new suspension components visible. 1984 Ford Bronco - The frame of a vehicle, likely from the 1980s, is shown with its fuel tank and suspension components. 1984 Ford Bronco - A black computer tower is shown with an attached device, possibly for audio or data processing.

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.