SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Join
1986 Ford Bronco
Home/ Registry/ Ford/ Bronco/ 1980–1986/ 1986 Bronco supermotors.net/registry/4636

1986 Ford Bronco

47 photos documented since 2004 ♡ Follow this build

Photos

1986 Ford Bronco - This 1986 Ford Bronco is parked in the snow, with a blue and tan exterior. 1986 Ford Bronco - Chrome exhaust headers are shown laid out on a wooden surface. 1986 Ford Bronco - A set of shiny chrome exhaust headers are shown mounted on a wooden surface. 1986 Ford Bronco - Two exhaust system parts, one a catalytic converter with the CATCO brand visible, are laid out on a wooden surface. 1986 Ford Bronco - Close-up view of the interior of a catalytic converter, showing the honeycomb structure with "12K" imprinted on it. 1986 Ford Bronco - This photo shows the interior of an exhaust pipe, not a 1986 Ford Bronco. 1986 Ford Bronco - This is a close-up view of the exhaust system's manifold and pipe connection, showing significant rust. 1986 Ford Bronco - Close-up view of an exhaust manifold and pipe connection, with visible rust and hardware. 1986 Ford Bronco - A close-up view shows a hole cut into an exhaust pipe, likely for a header installation. 1986 Ford Bronco - Cats and crossover pipe removed 1986 Ford Bronco - Passenger side installed. 1986 Ford Bronco - Drivers side installed 1986 Ford Bronco - No clearance between header and frame on passenger side. 1986 Ford Bronco - Starter looks like it will require header removal for access. A heat shield might also be a good idea. 1986 Ford Bronco - Collector exits lower than it should. Exhaust will have to rise up a couple inches to clear the tranny crossmember. 1986 Ford Bronco - 90 Bronco. O2 sensor placement? 1986 Ford Bronco - 90 Bronco. Lower t-crossmember? 1986 Ford Bronco - fuse panel diagram 1986 Ford Bronco - Poly hd motor mount from JBG 1986 Ford Bronco - Close-up of a corroded metal bracket with a pin, showing signs of wear and tear. 1986 Ford Bronco - Close-up view of a rusted metal bracket with a bolt and a cable, likely from a vehicle's undercarriage. 1986 Ford Bronco - Close-up of a custom-fabricated engine mount bracket. 1986 Ford Bronco - bottom of tranny mount 1986 Ford Bronco - Stock air inlet 1986 Ford Bronco - Temporary solution using 2"pvc pipe 1986 Ford Bronco - 3a Racing exhaust tip. End-view. 1986 Ford Bronco - 3a Racing tip. Side view 1986 Ford Bronco - Dynomax J-bend 1986 Ford Bronco - Loop style exhaust hanger 1986 Ford Bronco - O2 sensor fitting. 1986 Ford Bronco - Modified hangers 1986 Ford Bronco - header stud and header bolt. Studs aid in aligning the header while installing. I was only able to use 4 studs on the dirver side. The othe… 1986 Ford Bronco - after cutting 1986 Ford Bronco - Deburring the interior is easiest with a deburring tool. IExterior with a file. I used a file for both. 1986 Ford Bronco - The OD of the pipe through the bend radius is slightly smaller than the ID of the pipe through the straight section. 1986 Ford Bronco - Pipe from drivers side collector to the cat. 1986 Ford Bronco - Trimming a little off... 1986 Ford Bronco - Fully welded and ready to install... Almost. Still need to tweek a couple things (cut and reweld) but it's going on for now. 1986 Ford Bronco - Custom hanger installed. Passenger side to drivers side exit balances well at this point. I chose a simmilar point on the drvers side to pa… 1986 Ford Bronco - Cat forward view.
Browse all 47 photos

The peanut gallery

No comments yet — be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot — the owner approves it onto the record.