thedonor.jpg 508 hits | 63.42 KB | Posted: 12/28/05 This used to be a '79 F-250.
ttbgone.jpg 498 hits | 60.77 KB | Posted: 12/28/05 The TTB looks 10x better on the ground than it did in the truck. Good riddance
nofrontend2.jpg 672 hits | 55.18 KB | Posted: 12/28/05 No more ttb
nofrontend.jpg 464 hits | 57.9 KB | Posted: 12/28/05 TTB gone and the crossmember trimmed up a bit.
DSCN0491.JPG 438 hits | 87.45 KB | Posted: 12/28/05 Pee-Wee, Seemore's little brother and my daily driver, came down to the shop for moral support while...
DSCN0492.JPG 502 hits | 83.67 KB | Posted: 12/28/05 The rear-spring hanger mocked up. I think this will work
DSCN0493.JPG 794 hits | 89.87 KB | Posted: 12/28/05 Inside view of the mocked up driver's side hanger. We used the front stock hangers from the f-250 bu...
DSCN0500.JPG 568 hits | 92.32 KB | Posted: 12/28/05 Rear hangers in place and the springs on to verify the straightness of our mounting. Did pretty good...
DSCN0501.JPG 477 hits | 92.84 KB | Posted: 12/28/05 Another shot of the rear hanger with spring in place. Hangers are not quite done, will have to go ba...
truck 008.jpg 470 hits | 82.53 KB | Posted: 1/16/06 The front plate/crossmember welded in place
truck 009.jpg 485 hits | 77.77 KB | Posted: 1/16/06 another shot of the plate/crossmember
truck 016.jpg 506 hits | 83.25 KB | Posted: 1/16/06 This if the front spring hangers, made from the old channel crossmember we put in when the TTB was s...
truck 013.jpg 555 hits | 80.71 KB | Posted: 1/16/06 U-Bolt flip...had to make a new spring plate and grind down the cast part of the housing. I didn't l...
truck 012.jpg 619 hits | 83.65 KB | Posted: 1/16/06 The new spring plate...Cut it out from 1/4" plate and then cut two 1 1/2" strips to across the ends ...
truck 019.jpg 932 hits | 92.15 KB | Posted: 1/16/06 I hope this is the final install...New bushings in the springs, everything is lined up how I want it...
truck 022.jpg 864 hits | 87.2 KB | Posted: 1/16/06 Rear hangers are welded up good now..They are not goin anywhere. i think the frame will break in hal...
truck 023.jpg 838 hits | 95.58 KB | Posted: 1/16/06 Seemore is sittin on his new axle now. All he needs is brake lines and steering and a few odd & ends...
truck 024.jpg 493 hits | 87.49 KB | Posted: 1/16/06 Here it sits with the bumper my dad built for it. It's more than i had intended but he made it while...
truck 034.jpg 499 hits | 94.21 KB | Posted: 2/24/06 Shock mounts..The circles are peices I cut out to go in the hole where the original coil spring sat,...
truck 038.jpg 479 hits | 88.5 KB | Posted: 2/24/06 The cirle peices welded in
truck 039.jpg 481 hits | 85.07 KB | Posted: 2/24/06 Lower mount in place, I had to angle them towards the rear of the truck some to keep the shocks stra...
truck 042.jpg 494 hits | 91.02 KB | Posted: 2/24/06 Front end is pretty much done, this is first flex test, as much as I could do with a concrete slab a...
truck 031.jpg 549 hits | 90.76 KB | Posted: 2/24/06 this is only a temporary drag link..we shortened it a little too much and it doesn't drop down low e...
SAS
