calif 025.jpg
636 hits | 38.76 KB | Posted: 4/20/04
Shop towel holder constructed of D44 long side shaft, TTB radius arm brackets, D44 side gear

calif 026.jpg
603 hits | 48.74 KB | Posted: 4/20/04
The side gear is retained by a c-clip groove I cut

miscshop 011.jpg
551 hits | 54.79 KB | Posted: 5/11/04
Grinder pedestal. 8.8 with D44 spindle & hub on top

miscshop 012.jpg
508 hits | 76.96 KB | Posted: 5/11/04
worked the stock shock mount into the base

miscshop 013.jpg
504 hits | 73.93 KB | Posted: 5/11/04
this is my water pot, hope it holds water

miscshop 019.jpg
569 hits | 72.12 KB | Posted: 5/11/04
unlock the lockout, spin it around to the grinder of choice, re-engage lockout

miscshop 020.jpg
529 hits | 72.74 KB | Posted: 5/11/04
rear view, note the TTB sacrifice which watches over me at all times

miscshop 029.jpg
562 hits | 66.05 KB | Posted: 6/12/04
Floor jack lifted saddle, super handy

miscshop 032.jpg
484 hits | 76.84 KB | Posted: 6/12/04
The saddle is retained with a bit of a D44 pinion that drops into the jack, then hand-tighten the pi...

miscshop 035.jpg
501 hits | 87.42 KB | Posted: 7/17/04
Workbench receivers are very handy

jackextension.jpg
512 hits | 73.32 KB | Posted: 9/23/04
Another jack extension, this one 12" high

miscshop 040.jpg
486 hits | 57.75 KB | Posted: 10/21/04
axle holder; don't ask why the tubes are cut, I didn't do it

miscshop 042.jpg
501 hits | 56.67 KB | Posted: 10/21/04
hold-downs are modified 10.25 bearing caps

first half of spinner.jpg
510 hits | 70.38 KB | Posted: 10/28/04

miscshop 044.jpg
469 hits | 58.06 KB | Posted: 10/28/04

steelrack 001.jpg
536 hits | 87.77 KB | Posted: 11/18/04

steelrack 002.jpg
558 hits | 85.69 KB | Posted: 11/18/04

steelrack 004.jpg
525 hits | 61.8 KB | Posted: 11/18/04

steelrack 005.jpg
551 hits | 55.54 KB | Posted: 11/18/04

steelrack 006.jpg
546 hits | 82.03 KB | Posted: 11/18/04

steelrack 011.jpg
546 hits | 95.59 KB | Posted: 11/29/04

steelrack 014.jpg
474 hits | 97.37 KB | Posted: 11/29/04

steelrack 016.jpg
512 hits | 79.02 KB | Posted: 11/29/04

firewoodrack 004.jpg
427 hits | 79.98 KB | Posted: 11/22/04

firewoodrack 005.jpg
599 hits | 69.18 KB | Posted: 11/22/04

TTB8Lug 002.jpg
658 hits | 57.88 KB | Posted: 1/23/05
Shorter beam is 8 lug D44 HD TTB. Long beam is 5 lug TTB

TTB8Lug 001.jpg
708 hits | 55.73 KB | Posted: 1/23/05
The knuckles won't swap because ball joint spacing is different by approx 1/2". Note 8 lug knuckle ...

ranger 033.jpg
528 hits | 67.28 KB | Posted: 2/27/05
Cheap welding magnets just have a circular magnet surrounded by plastic

ranger 035.jpg
579 hits | 58.26 KB | Posted: 2/27/05
The plastic melts if exposed to high enough temps

deck 034.jpg
525 hits | 85.52 KB | Posted: 4/12/06

deck 035.jpg
518 hits | 79.53 KB | Posted: 4/12/06

miscshop 062.jpg
496 hits | 32.46 KB | Posted: 11/11/06

miscshop 062-2.jpg
426 hits | 27.87 KB | Posted: 11/11/06

miscshop 064.jpg
493 hits | 29.24 KB | Posted: 11/20/06

miscshop 068.jpg
520 hits | 39.64 KB | Posted: 11/20/06

miscshop 074.jpg
525 hits | 59.13 KB | Posted: 1/4/07

miscshop 075.jpg
600 hits | 54.75 KB | Posted: 1/4/07

miscshop 079.jpg
448 hits | 74.49 KB | Posted: 11/4/07

miscshop 078.jpg
400 hits | 72.55 KB | Posted: 11/4/07

miscshop 082.jpg
434 hits | 60.05 KB | Posted: 11/4/07

miscshop 084.jpg
461 hits | 50.58 KB | Posted: 11/11/07

miscshop 086.jpg
480 hits | 60.31 KB | Posted: 11/23/07

miscshop 095.jpg
402 hits | 78.92 KB | Posted: 12/29/07

miscshop 096.jpg
433 hits | 81.3 KB | Posted: 12/29/07

miscshop 098.jpg
439 hits | 59.45 KB | Posted: 12/29/07

miscshop 099.jpg
454 hits | 64.15 KB | Posted: 12/29/07

miscshop 100.jpg
380 hits | 34.77 KB | Posted: 12/29/07

gantry 001.jpg
475 hits | 68.33 KB | Posted: 1/2/08

gantry 005.jpg
478 hits | 48.32 KB | Posted: 1/2/08

gantry 007.jpg
554 hits | 72.5 KB | Posted: 1/2/08

gantry 009.jpg
737 hits | 32.1 KB | Posted: 1/2/08

gantry 011.jpg
786 hits | 42.42 KB | Posted: 1/2/08

gantry 010.jpg
864 hits | 53.38 KB | Posted: 1/2/08