SuperMotors SuperMotors SUPERMOTORS Search — try “orange Bronco on 35s”
Home/ Registry/ Ford/ Bronco/ 1980–1986/ “1BadBronco”/ 1995 Mustang 3G alt(ebay special) supermotors.net/registry/1967/21068

Album section

1995 Mustang 3G alt(ebay special)

From 1981 Ford Bronco “1BadBronco” — documented by Matt Kenney.

18 photos
1981 Ford Bronco - This was the voltage of my Main battery before the install. I dont think my battery is getting fully charged since its supposed to be about…This was the voltage of my Main battery before the install. I dont think my battery is getting fully charged since its supposed to be about… Owner 1981 Ford Bronco - Wow what a big difference. I removed the voltage regulator and all the dual battery stuff. leaving just enough to start the truck.Wow what a big difference. I removed the voltage regulator and all the dual battery stuff. leaving just enough to start the truck. Owner 1981 Ford Bronco - most years should have the same green and red wire. it goes from 12V S to your voltage regulator. It is now going to turn on the alt when t…most years should have the same green and red wire. it goes from 12V S to your voltage regulator. It is now going to turn on the alt when t… Owner 1981 Ford Bronco - underhood wiring. I cleaned and conduited all the wires. I still need to purchase a 150A fuze and megafuze holder. The only source I have f…underhood wiring. I cleaned and conduited all the wires. I still need to purchase a 150A fuze and megafuze holder. The only source I have f… Owner 1981 Ford Bronco - from the previous picture I found the wires wadded up to install these... so about 10 minutes of drilling and I had a temp mounting spot. A…from the previous picture I found the wires wadded up to install these... so about 10 minutes of drilling and I had a temp mounting spot. A… Owner 1981 Ford Bronco - I bought and soldered a new end on my short battery-solenoid cable since I cut it in half. 44 cents, some plumbing solder and a map gas tor…I bought and soldered a new end on my short battery-solenoid cable since I cut it in half. 44 cents, some plumbing solder and a map gas tor… Owner 1981 Ford Bronco - bought this today at the Stereo Shop 25 bucks for the holder and the 150A fuze. Not bad for some bling too.bought this today at the Stereo Shop 25 bucks for the holder and the 150A fuze. Not bad for some bling too. Owner 1981 Ford Bronco - blurry side viewblurry side view Owner 1981 Ford Bronco - close up of the fuze and holderclose up of the fuze and holder Owner 1981 Ford Bronco - Test fitting and making sure everything lines up.Test fitting and making sure everything lines up. Owner 1981 Ford Bronco - view from the bottom. I needed to run a nut and bolt now since the Alts mounting tab is straight threw instead of threaded.view from the bottom. I needed to run a nut and bolt now since the Alts mounting tab is straight threw instead of threaded. Owner 1981 Ford Bronco - slapping on the pulley... thats not gonna work.slapping on the pulley... thats not gonna work. Owner 1981 Ford Bronco - Going back to the best source for working on my truck... the internet... I bought some machine bushings and some washers. Unfortunatly 5/8"…Going back to the best source for working on my truck... the internet... I bought some machine bushings and some washers. Unfortunatly 5/8"… Owner 1981 Ford Bronco - this one fits, its got a little bit of play but it doesnt have to be snug.this one fits, its got a little bit of play but it doesnt have to be snug. Owner 1981 Ford Bronco - that will do it. Just enough to clearthat will do it. Just enough to clear Owner 1981 Ford Bronco - handy thought I had to tighten up the pully. The guy at the parts store that removed the serp belt one used an impact and held it with a pa…handy thought I had to tighten up the pully. The guy at the parts store that removed the serp belt one used an impact and held it with a pa… Owner 1981 Ford Bronco - test fitting this wiring harness I got from a 95 Taurus. I had to put on that terminal lug on the end of the yellow wire.test fitting this wiring harness I got from a 95 Taurus. I had to put on that terminal lug on the end of the yellow wire. Owner 1981 Ford Bronco - Pretty much done, just had to put the belt on and cover up that splice job with some electrical tape.Pretty much done, just had to put the belt on and cover up that splice job with some electrical tape. Owner