SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
Home/ Registry/ Ford/ Crown Victoria/ 1998-2011/ “SOLD”/ 2003 power LX seats in 2005+ P71 non-power pass. supermotors.net/registry/21648/72853

Album section

2003 power LX seats in 2005+ P71 non-power pass.

From 2007 Ford Crown Victoria “SOLD”, documented by mRdot.

27 photos
← Back to this vehicle
2007 Ford Crown Victoria - this is the floor connector view of the small connector for the air bag module RH passangerside in 2003 seats. 2007 Ford Crown Victoria - this is the floor connector view of the power seat motor harness, this connector type and wiring color codes didn't change from 1999-2008. 2007 Ford Crown Victoria - this is the 2003 RH seat custom connector view, you won't find this in the wiring diagrams manual published by Ford or anywhere else but he… 2007 Ford Crown Victoria - this is the 2007 LH custom connector view, you won't find this in the wiring diagrams manual published by Ford or anywhere else but here. 2007 Ford Crown Victoria - needed for install. stock wiring harnesses. extra color coded powerseat wiring (10 wires). RH powerseat door mounted switch. i used. 2003 d… 2007 Ford Crown Victoria - more donor wire. 2007 Ford Crown Victoria - RH door mounted 8-way powerseat switch. 2007 Ford Crown Victoria - 2003 connector view. left to right 1. side air bag module impact (2 wire connector) 2. basic seat connector (14 wire connector) 3. power se… 2007 Ford Crown Victoria - install the powerseat wiring harness though the black wiring runner, make sure you have enough to stick out to make your connection to the… 2007 Ford Crown Victoria - use this area pictured at the end of the wiring runner where the kick panel would go, for the ground wire 57 (BK) and tap into power from t… 2007 Ford Crown Victoria - powerseat wires are installed to the end of the wiring runner with enought sticking out to make another connection to the door wiring, that… 2007 Ford Crown Victoria - running the wiring though the door. there is an empty spot in the rubber to run the harness remove both ends and pushing it though the rubb… 2007 Ford Crown Victoria - connect the two wiring harnesses under the kick panel area and make sure to ground the two black wires and get about 3 feet of wire to tap… 2007 Ford Crown Victoria - updated 06/18/2012, pins 2 and 3 are only used with heated seats. 581 (RD) Heated Seats Off / High 1256 (WH/YE)Heated Seats Off / Low 2007 Ford Crown Victoria - the seats couldn't be rewired, airbag light kept coming on. so i removed the whole 2007 passenger seat wiring harness and parts (seatbelt a… 2007 Ford Crown Victoria - the 2007 RH passenger seat wiring harness that will be removed, and I'll also be removing the whole occupancy sensor pad. Both will be inst… 2007 Ford Crown Victoria - the 2003 LX passenger seat before. be gentle to the LX seats when removing the harness and use a soft mallet to stick the plastic retainers… 2007 Ford Crown Victoria - this is the problem source, the 2003 LX restraint control module. drill out the two rivets and remove the module. 2007 Ford Crown Victoria - on the left is a 2007 passanger side seat belt buckle and a 2003 passanger side on the right, as you can see another problem, you will need… 2007 Ford Crown Victoria - the 2007 occupancy sensor pad installed and tabbed in place in the 2003 LX seat frame. 2007 Ford Crown Victoria - the 2003 LX occupancy sensor pad that was removed. (slightly larger) 2007 Ford Crown Victoria - wiring is in place and lined up over the 2003 harness. i didnt remove the 2003 harness and the seat still functions 100% stock with both in… 2007 Ford Crown Victoria - connector view, I'll still be using 4 wires from the 2003 connector for power seat and recline. connectors from left to right powerseat - 2… 2007 Ford Crown Victoria - 2007 restraint control module riveted in place to the 2003 LX seat frame in the same spot as the 2003 RCM was in. 2007 Ford Crown Victoria - old 2003 restraint control module and some tools used. I had to drill out the rivits and re-rivit the 2007 module to the 2003 seat frame. 2007 Ford Crown Victoria - side view of the 2007 seatbelt insalled in the 2003 LX seat. 2007 Ford Crown Victoria - 2007-to-2003 LH custom wiring harness. the harness was made with a 2003 male (floor) and 2007 female (in seat) donor harness. making it pos…