P1040106.JPG
507 hits | 23.46 KB | Posted: 2/12/12
rear brake line adapter

PC300075.JPG
190 hits | 65.34 KB | Posted: 2/12/12
spring bow

PC300076.JPG
167 hits | 55.46 KB | Posted: 2/12/12
driver spring bow

PC300077.JPG
242 hits | 67.72 KB | Posted: 2/12/12
inital x-member trimming

PC310082.JPG
181 hits | 53.9 KB | Posted: 2/12/12
Ruff Stuffs RAW axle side trac bar mount ready for the knife. I think that the offset radius they cu...

PC310083.JPG
158 hits | 56.26 KB | Posted: 2/12/12

PC310085.JPG
166 hits | 57.68 KB | Posted: 2/12/12
Not quite there yet but getting close. The factory mount was tied into all of the other brackets so ...

PC310086.JPG
162 hits | 70.01 KB | Posted: 2/12/12
About where I would like it. The reason for the foward angle is to get it foward of the engine cross...

PC310087.JPG
173 hits | 70.61 KB | Posted: 2/12/12
A look at the angles. The factory bar is 37" from center of eye to center of eye it is also 15*...

PC310090.JPG
159 hits | 69.73 KB | Posted: 2/12/12

PC310091.JPG
192 hits | 72.1 KB | Posted: 2/12/12

PC310093.JPG
247 hits | 67.49 KB | Posted: 2/12/12
Frame side trac bar mount. I started with the Ruff Stuff Kit and made a few Mods. It will be safe.

PC310094.JPG
167 hits | 64.3 KB | Posted: 2/12/12

PC310095.JPG
181 hits | 83.43 KB | Posted: 2/12/12
A look at the uncleaned mount. I tried to tie the brackets back together. My goal was to have as muc...

PC310096.JPG
169 hits | 74.18 KB | Posted: 2/12/12
A look from a different angle.

PC310097.JPG
194 hits | 58 KB | Posted: 2/12/12

PC310098.JPG
204 hits | 43.1 KB | Posted: 2/12/12

PC310100.JPG
236 hits | 56.28 KB | Posted: 2/12/12
I really tried to get as much length as possible, that is why the angle extends beyond the frame. If...

PC310101.JPG
225 hits | 61.13 KB | Posted: 2/12/12

PC310102.JPG
361 hits | 50.63 KB | Posted: 2/12/12
A full stuff look and the trac bar and the engine cross member clearance. Should be good to go. I do...

PC310103.JPG
260 hits | 58.03 KB | Posted: 2/12/12
Full stuff driver side, I may have to clearance the angle I used for the base of the mount. We'll se...

PC310104.JPG
261 hits | 60.9 KB | Posted: 2/12/12

PC290065.JPG
218 hits | 62.41 KB | Posted: 2/12/12
I myself have driven about 95K on this axle. It has served.

P1070116.JPG
209 hits | 50.42 KB | Posted: 2/12/12
Where the bracket lives, this centers the axle in the fender. Is the same place as mwalsh put his.

PC300067.JPG
216 hits | 67.45 KB | Posted: 2/12/12
Another reference for location. The hole that you can see is oval shaped

PC300068.JPG
250 hits | 72.17 KB | Posted: 2/12/12
The best locate, the 2 holes you can see are factory. The foward hole you can see was used for the r...

P1060109.JPG
191 hits | 63.77 KB | Posted: 2/12/12

P1060110.JPG
183 hits | 60.83 KB | Posted: 2/12/12

P1060111.JPG
200 hits | 54.94 KB | Posted: 2/12/12

P1060112.JPG
192 hits | 58.36 KB | Posted: 2/12/12

P1060113.JPG
182 hits | 53.14 KB | Posted: 2/12/12

P1060115.JPG
195 hits | 85.18 KB | Posted: 2/12/12

P1070122.JPG
184 hits | 57.12 KB | Posted: 2/12/12

P1070123.JPG
253 hits | 81.15 KB | Posted: 2/12/12

P1070125.JPG
229 hits | 86.65 KB | Posted: 2/12/12

P1070124.JPG
278 hits | 69.85 KB | Posted: 2/12/12

P1070121.JPG
301 hits | 79.09 KB | Posted: 2/12/12

P1100128.JPG
233 hits | 56.25 KB | Posted: 2/19/12

P1100129.JPG
234 hits | 66.66 KB | Posted: 2/19/12

P1110132.JPG
382 hits | 58.71 KB | Posted: 2/19/12
The ho's.

P1110134.JPG
229 hits | 52.09 KB | Posted: 2/19/12

P1110135.JPG
241 hits | 50 KB | Posted: 2/19/12

P1120137.JPG
300 hits | 76.51 KB | Posted: 2/19/12

P1200147.JPG
387 hits | 81.19 KB | Posted: 2/28/12
Purpose modded Bronco preping for the first tow!! She did well. Made a 40 mile trek on HWY 101 which...

P1280150.JPG
434 hits | 69.61 KB | Posted: 3/8/12
As mentioned earier I have no E-brake. I had a local motorcycle shop shorten and solder a end on a F...

P1280152.JPG
290 hits | 62.07 KB | Posted: 3/8/12

P1280153.JPG
343 hits | 65.45 KB | Posted: 3/8/12
Roughing out the bracket thing. I think this might be called a yoke.

P1280154.JPG
299 hits | 71.95 KB | Posted: 3/8/12

P1290155.JPG
331 hits | 76.16 KB | Posted: 3/8/12
The final install. I had to open the 2 holes that go to the rear brakes a touch to get the ends in, ...

P7220239.JPG
212 hits | 47.5 KB | Posted: 9/16/13
The Boat!! The purpose of my Bronco!

P7220240.JPG
204 hits | 51.03 KB | Posted: 9/16/13