1995 Ford Bronco pictures, photos, videos, and sounds

MarktheShark > 1995 Ford Bronco

1995 Ford Bronco

Owner:	MarktheShark
From:	Aurora, CO, U.S.A. (Other registries in CO)
Year, Make, & Model:	1995 Ford Bronco (Other Ford Broncos)
Avatar:
Nickname:
Mileage:	88
Engine:	5.8L 351cu
Drivetrain:	Dana 44 8.8" rear end 3.55
Notes:
Last Updated:	4/17/2019
Hits:	7324

Album

Folder				Hits		Created	Updated
My Bronco Pics	4	0	0	1,008	0	12/6/13	1/17/18
Master Cylinder Pics	2	0	0	297	0	12/27/13	12/27/13
Tie Rod Ends	4	0	0	386	0	3/15/14	3/15/14
Differential Tag	1	0	0	290	0	3/15/14	3/15/14
What the hell is this?	2	0	0	229	0	3/22/14	12/9/16
Random Hose	1	0	0	104	0	4/18/14	4/18/14
Rear Drive Shaft Yoke	1	0	0	103	0	4/24/14	4/24/14
Dodge Nitro Cushion Install	8	0	0	2,696	0	4/27/14	4/27/14
Front ABS	1	0	0	92	0	5/16/14	5/16/14
Front ABS sensor install	3	0	0	1,399	0	5/22/14	5/22/14
Saginaw Upgrade	10	0	0	952	0	6/2/14	6/27/14
Random Harness	1	0	0	80	0	6/4/14	6/4/14
Top Radiator Line/Hose	1	0	0	83	0	6/4/14	6/4/14
Tailgate Rust	3	0	0	293	0	7/7/14	7/7/14
Old Printout	1	0	0	74	0	8/13/14	8/13/14
Windshield Wiper Stud	0	0	1	783	0	10/7/14	10/7/14
Stuff to Sell	11	0	0	857	0	1/4/15	12/11/17
Console	6	0	0	508	0	1/4/15	1/4/15
More stuff to sell	14	0	0	912	0	1/4/15	10/20/17
Random stuff	16	0	0	1,318	0	7/12/15	2/4/19
1356 Transfer Case	6	0	1	1,022	0	5/12/15	3/5/19
Brake Lines	2	0	0	251	0	7/12/15	7/12/15
Tie rods	1	0	0	50	0	6/11/18	6/12/18
York210 Install	1	0	1	194	0	4/17/19	4/17/19

Newest Media Files

A/C delete with spacers to work with the York Bracket.

IMG_4081.jpg
79 hits | 74.53 KB | Posted: 4/17/19
A/C delete with spacers to work with the York Bracket.

York Running with PSC pump and A/C delete

A:C_York.MOV
115 hits | 17.08 MB | Posted: 4/17/19
York Running with PSC pump and A/C delete

IMG_3944.MOV
111 hits | 20.76 MB | Posted: 3/5/19
Front Output/TC

Switch panel.jpg
70 hits | 51.19 KB | Posted: 2/4/19
Switch Panel

bezel2.jpeg
60 hits | 48.04 KB | Posted: 12/19/18
New bezel 2

Bezel1.jpeg
78 hits | 82.21 KB | Posted: 12/19/18
New Bezel

IMG_3623.jpg
115 hits | 69.6 KB | Posted: 10/22/18
Bar length close

IMG_3624.jpg
84 hits | 79.34 KB | Posted: 10/22/18
bar length full

IMG_3625.jpg
98 hits | 94.02 KB | Posted: 10/22/18
Linkage plate front

Most Viewed Files

I had to drill out the passenger side bolt. The points were completly rusted and gone. I'm pissed at myself that I ended up being off center becasue I got impatient. All in all I think I am lucky. It didn't break all the way through, so I think I can...

Broken ABS shield.JPG
1055 hits | 82.87 KB | Posted: 5/22/14
I had to drill out the passenger side bolt. The points were completly rusted and gone. I'm pissed at myself that I ended up being off center becasue I got impatient. All in all I think I am lucky. It didn't break all the way through, so I think I can...

$Not sure if "wiper stud" is the proper word for it, but since I have had this ride, the driver's side wiper hasn't gotten the rain off the best. I believe this is the reason why. The passenger side moves in and out, but its a fraction of wh...$

Windshield Wiper Stud.MOV
783 hits | 612.15 KB | Posted: 10/7/14
Not sure if "wiper stud" is the proper word for it, but since I have had this ride, the driver's side wiper hasn't gotten the rain off the best. I believe this is the reason why. The passenger side moves in and out, but its a fraction of wh...

Yeah.jpg
450 hits | 40.51 KB | Posted: 12/6/13

Bought this dodge nitro cushion on ebay for a decent price.

Dodge Nitro Cushion.JPG
428 hits | 47.39 KB | Posted: 4/27/14
Bought this dodge nitro cushion on ebay for a decent price.

After removing the seat and separating the bottom from the back, I was able to move the new cushion into position for the OE seat cover to fit well. I had to put in a little bit of the foam in order to fill out the sides. Nothing that is going to mat...

New Cushion installed.JPG
369 hits | 59.4 KB | Posted: 4/27/14
After removing the seat and separating the bottom from the back, I was able to move the new cushion into position for the OE seat cover to fit well. I had to put in a little bit of the foam in order to fill out the sides. Nothing that is going to mat...

A view fully installed. Removal, cushion install and seat install took about 45 mins.

Full Installed.JPG
360 hits | 33.98 KB | Posted: 4/27/14
A view fully installed. Removal, cushion install and seat install took about 45 mins.

This is my OE cushion with some foam that I installed. It worked ok, but it still wasn't right. The left side of the cushion was so collapsed it was going to be tough to fix. With some time and patience, I probably could have gotten it right.

Original Cushion with foam.JPG
345 hits | 49.17 KB | Posted: 4/27/14
This is my OE cushion with some foam that I installed. It worked ok, but it still wasn't right. The left side of the cushion was so collapsed it was going to be tough to fix. With some time and patience, I probably could have gotten it right.