SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
Home/ Registry/ Ford/ Bronco/ 1992–1996/ “Big Pig”/ 3/4 ton upgrade supermotors.net/registry/37/13417

Album section

3/4 ton upgrade

From 1995 Ford Bronco “Big Pig”, documented by pepper.

41 photos
← Back to this vehicle
1995 Ford Bronco - Sterling 10.25 from a 95 F250 1995 Ford Bronco - fawker is heavy 1995 Ford Bronco - 8 lug D44 goodies 1995 Ford Bronco - spindles 1995 Ford Bronco - 8.8 rear w/ 4.56 gears, Detroit locker, and LPW bearing support cover. I'd like to go with a slightly higher (numerically) ratio and an ARB… 1995 Ford Bronco - Extreme close-up inside an open differential housing showing the ring gear teeth meshing with the pinion gear, with the ring-gear-mounted s… 1995 Ford Bronco - 8.8's axle seal took a walk. 1995 Ford Bronco - 8.8's shaft scored up again. 1995 Ford Bronco - bearings shot too, again. I believe this housing is bent. 1995 Ford Bronco - so I guess the sterling is going in sooner than I had planned. 1995 Ford Bronco - tried gringing off the perches in order to relocate them but got uncomfortable when I got to this and still couldn't get them off. So I jus… 1995 Ford Bronco - getting there... 1995 Ford Bronco - Now that's a good friend. My buddy Mike is loaning me his bronco, while mine is out of service. 1995 Ford Bronco - little dolly I made to roll this thing around 1995 Ford Bronco - 16.5x9.75 wheels. Decided on 16x10 589's instead of these. 1995 Ford Bronco - A complete rear axle assembly with center differential housing resting on a wooden pallet in a garage, a chrome wheel mounted at each end;… 1995 Ford Bronco - 8.8 gone (again) 1995 Ford Bronco - just trying to get it under there... 1995 Ford Bronco - still need to make/buy u-bolt plates or modify the old ones. I had new 5/8 u-bolts made at a local shop. 1995 Ford Bronco - D44 8 lug rotors 1995 Ford Bronco - D44 8 lug spindles, calipers, stands, brackets, pads, and Sterling's new U-bolts. 1995 Ford Bronco - made these out of 1/2" plate. not sure how they'll hold up. I may need to weld some supports across them if they start to bend. Just had no… 1995 Ford Bronco - Plates seem fine right now. Still might cut that extra length off of the u-bolts later in order to get a socket over them. 1995 Ford Bronco - seeing how the wheels fit. 1995 Ford Bronco - Tires will be here tomorrow. 1995 Ford Bronco - Been hard to work lately with this on my arm. Fried turkey fell back in the pot after it was being pulled out. 1995 Ford Bronco - A white Ford Bronco sits wheel-less on jack stands in a driveway during a suspension build, three-quarter front view with the front axle an… 1995 Ford Bronco - White full-size Ford Bronco XL up on jack stands in a driveway at dusk with all four wheels off, exposing the front axle, coil springs, rad… 1995 Ford Bronco - Close-up of a front hub and vented brake rotor with 8-lug wheel studs and a locking hub assembly, shown with the vehicle raised on gray jac… 1995 Ford Bronco - 37x13 Boggers on 16x10 Eagle 589 wheels. 1995 Ford Bronco - Next to my old 36x14.50 Mickey Thompson Baja Belted on 15x12 Eagle 589 wheels 1995 Ford Bronco - One wheel came with 8 on 170mm bolt pattern... what, should I be surprised? 1995 Ford Bronco - Lifted white full-size Ford Bronco photographed from the side in a driveway, sitting on a jack stand with tools on the concrete beside it.… 1995 Ford Bronco - Rear view of a lifted white Ford Bronco on a driveway, riding on tall mud-terrain tires with a black tubular rear bumper carrying D-ring sh… 1995 Ford Bronco - Front view of a white lifted Ford truck on jack stands in a driveway with the passenger-side front wheel and hub removed, exposing the soli… 1995 Ford Bronco - Three-quarter rear view of a white lifted Ford Bronco parked on a concrete driveway, with a black tube rear bumper, D-ring shackles, and a… 1995 Ford Bronco - Taking it to get the driveshaft made and 4.56's and detroit installed 1995 Ford Bronco - Cool tow truck 1995 Ford Bronco - Ford 3/4 ton D44 spindle with a Ford 1/2 D44 spindle 1995 Ford Bronco - dual piston calipers and 16" wheels 1995 Ford Bronco - Driveshaft. 1350 double-cardan and 1410 yoke. Made by Advance Driveline in Orlando.